User manual H2O AUDIO S6-1A3

[. . . ] H2O Audio has provided an extra T-Seal (included) in the event of annually replacement, accidental damage, loss, overexposure to direct sunlight, or if the T-Seal has become misshaped though misuse. To install a new or clean T-Seal, start at any corner, push the T-Seal into the corner and run your finger along the T-Seal pushing it into the Housing Contact Surface. 4. Ensure the T-Seal is seated properly in all four corners and the Housing Contact Surface. How to install / replace the T-Seal 5. If you experience any resistance when closing the housing please call customer service immediately at 1. 800. 708. 6080 x213 before using your housing. Cleaning & Storing the T-Seal It is extremely important that you keep the T-Seal clean & free of sand, dirt, hair, lint, and other debris. [. . . ] Installing the iPod into the Housing Installing the iPod 1 1 1. Close the lid, and hook the buckle under the base. Contact Surfaces iPod nano Housing Water IT IS EXTREMELY IMPORTANT YOU ENSURE THE T-SEAL IS PROPERLY SEATED DURING EACH CLOSURE. If it is out of alignment, or twisted you will cause damage to or destroy your iPod. 2 2 1. Align the audio port with the stereo jack in the housing. IMPORTANT: Remove any skins or covers from your iPod before installing it into the housing. 2. Verify the player is completely plugged into the audio jack. Prior to use, verify: Do NOT use if: 2. While holding the latch button towards the unlock icon, push up on the side of the latch. 2. T-Seal is aligned properly in the Contact Surface of the lid prior to closure. 1. T-Seal and contact surface have been cleaned as necessary using a soft, lint-free cloth. 2. T-Seal and Contact Surfaces have any dirt, lint, hair, and/or other debris. Removing the iPod 1. Now the player can slide straight out of the housing. 3. 3 T-Seal and Contact Surface are free of scratches and other imperfections. 3. You see scratches or imperfections on the T-Seal or Contact Surfaces. 3. Unhook the buckle from the base. and the button is positioned on the icon prior to entering the water. DO NOT USE SILICONE GREASE as this will damage the seal. To ensure the T-Seal is fully seated in the base of the housing, firmly squeeze both sides (the base and lid) of the housing together after each insertion of the player. Always check to make sure the latch is closed and locked prior to use. If you have any questions or doubts, please contact H2O Audio Customer Support NOTE: Do not disturb the T-Seal during removal of the player. If the T-Seal is moved, Please use the housing lid to completely seat the T-Seal. S6 - 70 20060531 8. Connecting the Headphones The SealTight Connector is what keeps your audio connection safe and dry underwater. It is designed specifically to create a seal around the H2O Audio Series Waterproof Headphones (sold separately). Using any other headphones will not have a complete waterproof connection, and reduces the waterproof rating to water-resistant. TM 9. CommanderTM Scroll Wheel Control The Commander Scroll Wheel Control is a waterproof assembly, which allows you to maintain complete control over the iPod's Click wheel functions. Refer to iPod Instruction Manual for complete details of how to use the player. TM 10. General Storage Procedures For long-term storage, store in a plastic bag out of direct sunlight. Do not expose the housing to extreme heat, such as the inside of a hot car, or in hot direct sunlight, such as on a beach, or boat deck. [. . . ] IF YOU EXPERIENCE RINGING IN YOUR EARS, REDUCE VOLUME OR DISCONTINUE USE. THE MANUFACTURER DOES NOT WARRANT AND WILL NOT BE HELD RESPONSIBLE IN ANY WAY FOR DAMAGES TO THE iPod, OR LOSS OF DATA, INCLUDING LOSS OF DATA STORED IN THE iPod, RESULTING FROM AN EXCESSIVE IMPACT, THUNDER, OR AN EORED ON YOUR DEVICE. Pro Armband for extreme sports Swimbelt designed by swimmers 12. Contact Us Customer Support is available Monday to Friday 9AM to 5PM PST. support@h2oaudio. com Copyright Notice: This owner's manual is copyrighted, all rights reserved. [. . . ]