User manual H2O AUDIO IN3-5A3

[. . . ] If you experience any resistance when closing the case please call customer service immediately at 1. 800. 708. 6080 before using the case. Visually inspect the outside of the case and ensure the T-seal is installed correctly. If the T-Seal is dirty, out of alignment, twisted or pinched in any way it will compromise the integrity of the case and should not be used. Cleaning & Storing the T-Seal It is extremely important that you keep the T-Seal clean & free of sand, dirt, hair, lint, and other debris. Wash T-Seal in warm fresh water, ensuring all debris is cleaned from the T-Seal. [. . . ] Unlocking & Locking the Case Unlocking your case Locking your case 6. The T-Seal T-Seal The removable, black, T-Seal (retained in the lid), between the base and the lid of the case is, what keeps your iPod safe and dry. T-Seal iPod nano Housing Water 7. Installing the iPod into the Case Installing the iPod Contact Surfaces 1. Close the lid, and hook the buckle under the base. IT IS EXTREMELY IMPORTANT YOU ENSURE THE T-SEAL IS PROPERLY SEATED DURING EACH CLOSURE. If it is out of alignment or twisted you will cause damage to or destroy your iPod. Align the audio port with the stereo jack in the case. IMPORTANT: Remove any skins or covers from your iPod before installing it into the housing. 2. While holding the latch button towards the unlock icon, push away from the case to open the latch. 1. T-Seal is twisted or out of alignment during closure. Compatible with iPod nano (3rd Gen) 2. Pull the latch towards the case and snap close. Contact Surface of the lid prior to closure. Removing the iPod 1. T-Seal and contact surface have been cleaned as necessary using a soft, lint-free cloth. 2. T-Seal and Contact Surfaces have any dirt, lint, hair, and/or other debris. 3. T-Seal and Contact Surface are free of scratches and other imperfections. 3. You see scratches or imperfections on the T-Seal or Contact Surfaces. 3. Unhook the buckle from the base. with the button positioned on the icon prior to entering the water. Verify the T-Seal is aligned properly. DO NOT USE SILICONE GREASE as this will damage the seal. To ensure the T-Seal is fully seated in the base of the case, firmly squeeze both sides (the base and lid) of the case together after each insertion of the player. Always check to make sure the latch is closed and locked prior to use. If you have any questions or doubts, please contact H2O Audio Customer Support NOTE: Do not disturb the T-Seal during removal of the player. If the T-Seal is moved, Please use the case lid to completely seat the T-Seal. iN3 - 70 20071106 8. Connecting the Headphones The SealTight Connector is what keeps your audio connection safe and dry underwater. It is designed specifically to create a seal around the H2O Audio Waterproof Headphones (sold separately). Using any other headphones will not have a complete waterproof connection, and reduces the waterproof rating to water-resistant. TM 9. CommanderTM Scroll Wheel Control The Commander Scroll Wheel Control is a waterproof assembly, which allows you to maintain complete control over the iPod's Click wheel functions. Refer to iPod Instruction Manual for complete details of how to use the player. TM 10. [. . . ] IF YOU EXPERIENCE RINGING IN YOUR EARS, REDUCE VOLUME OR DISCONTINUE USE. THE MANUFACTURER DOES NOT WARRANT AND WILL NOT BE HELD RESPONSIBLE IN ANY WAY FOR DAMAGES TO THE iPod, OR LOSS OF DATA, INCLUDING LOSS OF DATA STORED IN THE iPod, RESULTING FROM AN EXCESSIVE IMPACT, THUNDER, OR AN ELECTRICITY FAILURE, OR WATER DAMAGE. YOU WILL BE RESPONSIBLE FOR SAFE GUARDING ALL DATA STORED ON YOUR DEVICE. 14. Warranty Coverage H2O Audio guarantees, to the original purchaser only, that the equipment purchased (EXCLUDING THE iPod ) is free of defects in material and/or under normal recreational use for a period of one year (1) from date of consumer purchase from an Authorized Dealer; provided that proper care and maintenance have been performed as prescribed by the owner's guide included with the equipment. [. . . ]