User manual GTO PRO-SW 4000XL MASTER

[. . . ] Installation Manual for the DC-SERIES ® SINGLE Gate Operator System FOR PROFESSIONAL INSTALLATION ONLY! This equipment is similar to other gate or door equipment and meets or exceeds Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has hazards associated with its use and therefore by installing this product the installer and user accept full responsibility for following and noting the installation and safety instructions. Failure to follow installation and safety instructions can result in hazards developing due to improper assembly. You agree to properly install this product and that if you fail to do so GTO, Inc. [. . . ] The control box must be mounted at least 3 feet above the ground to protect it from rain splash, snow, etc. , and at least 3 feet from an AC power source to prevent electrical interference. Use mounting holes and screws provided to mount control box to a secure surface. 15 FUSE SWITCH GTO, Inc. 3121 Hartsfield Rd Tallahassee, FL 32303 ALARM BAT­ www. gtoinc. com 800-543-GATE BAT+ DUAL ON MODES 1 1234 2 3 4 ON OFF SET LIMIT MODES ON 1 1 2 3 4 5 6 7 ON 2 3 4 5 6 7 OFF LEARN TRANSMITTER SWITCH 10' 12' 14' 8' GATE LENGTH 16' ~~ 18VAC ­ + NC RLY-COM NO SOLAR RELAY OUT CYCLE CLOSE CLOSE EDGE EXIT/ OPEN SLAVE INPUTS MASTER INPUTS OPEN EDGE GRN WHT BLUE BRN ORG RED BLK GRN WHT BLUE BRN ORG RED BLK COM COM SAFETY SHADOW LOOP GRN BLK RECEIVER RED 17 Connecting Operator Power Cable Step 2 Strip approximately 3/16" of insulation from each wire of the operator power cable. Twist each exposed wire tightly (there are seven [7] wires inside the power cable sheath). Thread approximately 6" of the power cable into the control box and retighten sealing nut until the power cable locks into place. ~~ 18VAC ­ + NC RLY-COM NO SOLAR RELAY OUT 15 FUSE SWITCH GTO, Inc. 3121 Hartsfield Rd Tallahassee, FL 32303 ALARM BAT­ 800-543-GATE www. gtoinc. com BAT+ DUAL ON MODES 1 1234 2 3 4 ON OFF SET LIMIT MODES ON 1 1 2 3 4 5 6 7 ON 2 3 4 5 6 7 OFF LEARN TRANSMITTER SWITCH 10' 12' 14' 8' GATE LENGTH 16' CYCLE CLOSE CLOSE EDGE EXIT/ OPEN SLAVE INPUTS MASTER INPUTS OPEN EDGE GRN WHT BLUE BRN ORG RED BLK GRN WHT BLUE BRN ORG RED BLK COM COM SAFETY SHADOW LOOP GRN BLK RECEIVER RED Strain Relief Lock Nut Hub Sealing Nut Strain Relief Step 3 Operator Power Cable Insert the stripped operator power cable wires into the appropriate terminals on the OPERATOR terminal block. The green wire should be inserted into the GRN terminal, the blue wire into BLU, the orange wire into ORG, black wire into BLK, and the red wire into the RED terminal. A dab of petroleum jelly on each terminal will help prevent corrosion. Do not overtighten. Correct Wrong Wrong SWITCH GRN WHT MASTER INPUTS J13 J5 BLUE BRN ORG RED BLK Power cable from operator (master) arm CYCLE CLOSE SAFETY EXIT OPEN SHADOW LOOP CLOSE EDGE OPEN EDGE COM COM GRN J11 J8 MIN STALL FORCE RECEIVER J12 BLK Wire Installing the Battery Step 4 Make sure the control box power switch is in the OFF position. Remove the control box cover and slide the battery into position with its terminals to the RIGHT (see illustration). Connect the BLACK battery wire to the NEGATIVE (­) battery terminal. Pay close attention to the color of the BLACK wire to NEGATIVE (--) terminal wires. If the wires are connected incorrectly, the control board may be damaged. RED wire to POSITIVE (+) terminal NEVER insert the battery with the terminals to the left. BLACK NOTE: The battery that came with your GTO/PRO® 4000, MUST be placed horizontally battery with the terminals on the RIGHT. If an optional second battery is needed, both batteries must be placed vertically with terminals at the bottom. An optional second battery can be used for solar and/or high traffic applications, if needed. Single Battery Installed Horizontally with terminals on the right. Dual Batteries Installed Vertically with terminals on bottom. 18 MAX Terminal Block Wire Terminal Block Wire Terminal Block RED RED Powering the System IMPORTANT: · · Installation of the Transformer The transformer is designed and intended for indoor use. If the transformer can be plugged only into an outside electrical outlet, a weatherproof cover or housing (available at local electrical supply stores) must be used. All low voltage wire used with the GTO/PRO® 4000 Gate Operator must be 16 gauge dual conductor, multi-stranded, direct burial wire (see page 20) and the Accessory Catalog). from an ac power source, you will need to use at least one 5 watt Solar Panel to charge the battery (see Accessory Catalog). Refer to the Solar Panels and Gate Activity chart below. · Optional Solar Panels and Gate Activity The table and map illustrate the maximum number of gate cycles to expect per day in a particular area when using from 10 to 30 watts of solar charging power. The figures shown are for winter (minimum sunlight) and do not account for the use of any accessory items. Accessories connected to your system will draw additional power from the battery. NOTE: A minimum of 10 watts of solar charging power is required for GTO/PRO 4000 single gate systems, with a maximum of 30 watts. [. . . ] Key Chain Mini Transmitter (RB744) The Key Chain Mini Transmitter is a miniature version of the GTO/PRO® entry transmitter and has the same adjustable code settings. Entry Transmitter (RB741) The GTO/PRO® entry transmitter, with adjustable code settings, is standard equipment with all GTO/PRO® systems. Digital Keypad (F300) The specially designed digital keypad can be easily installed as a wireless or wired keypad. It can be programmed to use up to fifteen different personal identification number (PIN) codes. [. . . ]