User manual GTO PRO-SW 2000

[. . . ] ¨ + LIS TED 75 SERIES AUTOMATIC GATE OPERATOR FOR VEHICULAR SWING GATES INSTALLATION MANUAL FOR THE PROFESSIONAL INSTALLER Receiver Control Box with Battery Post Bracket Assembly 120 Volt Indoor Transformer (surge protector not supplied) Warning Sign Gate Bracket GTO/PRO 2000 Power Cable Closed Position Positive Stop Plate Run 1000' (max. ) of low voltage wire to control box from transformer. (wire not included) PVC conduit (not included) to protect wire from lawn mowers and weed eaters. WARNING! READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before attempting to install and use this automatic gate operator. Stay clear of the unit while it is operating and exercise caution at all times. This product meets and exceeds the requirements of UL 325, the standard which regulates gate operator safety, as established and made effective March 1, 2000, by Underwriters Laboratories Inc. 3121 Hartsfield Road · Tallahassee, Florida, USA 32303 Telephone GTO Sales: 1-800-543-GATE (4283) or (850) 575-0176 · Fax (850) 575-8912 or GTO Technical Service: 1-800-543-1236 or (850) 575-4144 · Fax (850)575-8950 1 www. gtoinc. com RB923 rev - 06/03/02 ©2000 GTO, Inc. GTO/PRO 2000 series automatic gate operators are intended for use with vehicular swing gates. These operators can be used in Class I, Class II and Class III applications. [. . . ] A dab of household petroleum jelly on each terminal will help prevent corrosion. RED BLACK Power Cable from First Operator Low Voltage Wire from AC Transformer Step 25: Strip 1/2" off the ends of the low voltage wire and attach ends to the transformer terminals; red lead to RED, black lead to BLK. A dab of household petroleum jelly on each terminal will help prevent corrosion. We recommend crimping a spade-tongue terminal (not provided) to the end of each wire before attaching it to the transformer. Make sure the exposed wires DO NOT touch each other! Spade Tongue Terminal (not provided) Red Black Step 26: Plug in the transformer. We strongly recommend using a surge protector with the transformer. HINT: Keep a few mothballs in the control box to discourage insects from entering it and damaging the control board. 21 CONTROL BOARD SETTINGS DIP Switches The four DIP switches on the control board match the operator with the type of gate on which it is installed. Prior to packaging, the GTO/PRO 2000 series control board was configured for single swing gates that pull-to-open (open into the property). If your gate type matches this configuration, you DO NOT need to adjust the DIP switches; Proceed to the Potentiometers section on the next page. NOTE: To change the DIP switch settings, you must turn the control box power switch OFF; move the switch; then turn the power back ON. Use a small screwdriver to move the switches. DIP switches OBSTRUCT SENS. PULL/PUSH: Set to PULL for swing gates that pull-toopen [factory setting]; PUSH for swing gates that push-toopen (see Push to Open Installation on pages 31-32). NOTE: The direction a gate opens is determined by standing inside the property and facing toward the gate. SNGL/DUAL: Set to SNGL for a single gate leaf [factory setting]; DUAL for dual gate leaves. See Dual Gate System Installation on page 40 for more information (the factory setting is OFF). STATUS PULL/PUSH SNGL/DUAL SEQ1 SEQ2 4 ON 1 2 3 MIN MAX LEARN LOSE AUTOC 60 W. SEN MAX USH PULL/P L UA SNGL/D SEQ1 SEQ2 MIN LEARN G RB OPN EDG CLS EDG OPN EDG CLS EDG ORG BLU GRN RED BLK ORG BLU GRN GRN ORG BLU WHT BLK RED SOLAR 18VAC ­ + ~~ SECO FIRST POWE R IN N RAT D OPE OR ALAR M ACCE SSOR Y RCVR OPER ATOR 22 Potentiometers The three (3) potentiometers on the control board operate like a volume control on a radio. They control the auto close timer, inertia, and obstruction sensitivity of the operator. Use a small slotted screwdriver to turn the arrow in the center of the potentiometer. AUTO CLOSE (auto close timer): Determines how long the gate will remain open before it automatically closes. INERTIA: Fine tunes obstruction sensitivity in the opening and closing modes. INERTIA allows the opener to attempt to push an obstruction clear of the gate path. When INERTIA is set to MIN the opener will obstruct quickly (i. e. , will attempt to push an obstruction briefly); when set to MAX, the opener will obstruct slowly (i. e. , will push against an obstruction for a longer period). (obstruction sensitivity): Determines the amount of force exerted by the gate on an obstruction before the operator stops and reverses. When set to MAX, the operator will exert maximum gate force before obstructing (i. e. , the operator will require greater resistance before stopping and reversing. ). [. . . ] Particularly suited for remote installations, the solar panel comes with tubular steel support, mounting clips, wire connectors, and 8 ft. Installation in some regions of the world will require multiple panels for adequate charging power. Recommended for GTO/PRO 1000, GTO/PRO 1200 and the GTO Bulldog Gate Lock. Dual gate installations require minimum of two (2) 5 watt solar panels for adequate charging power. 43 ACCESS -ories Standard Replacement Transformer (RB570) ­ Standard 18 Volt, 40 VA, AC transformer for chargingthe battery included with the GTO/PRO 2000 series gate operators. Bulldog Replacement Charger (RB421) ­ Standard 12 volt DC charger (not shown) for maintaining battery included with the Bulldog Pedestrian Gate Lock. Replacement Batteries RB500 ­ The standard 12 volt, 7. 0 ampere-hour, maintenance-free battery for all GTO/PRO gate operators. RB422 ­The 12 volt, 1. 2 ampere-hour version for use with the Bulldog Pedestrian Gate Lock. Replacement Receivers The AQ201: Receiver with a 10 ft. [. . . ]