User manual GTO PRO-SL 1000

[. . . ] FOR VEHICULAR SLIDE GATES INSTALLATION MANUAL FOR THE PROFESSIONAL INSTALLER AUTOMATIC GATE OPERATOR This equipment is similar to other gate or door equipment and meets or exceeds Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has hazards associated with its use and therefore by installing this product the installer and user accept full responsibility for following and noting the installation and safety instructions. Failure to follow installation and safety instructions can result in hazards developing due to improper assembly. You agree to properly install this product and that if you fail to do so GTO, Inc. [. . . ] To prevent damage to transformer, make sure the exposed wire ends do not touch each other! Spade Tongue terminal Red Black DO NOT plug the transformer into outlet. The transformer will be plugged in during STEP 13. NOTE: Wires coming from the ground to the control box should be run through PVC conduit to protect them from lawn mowers, weed eaters and grazing animals (see illustrations on page 13). Illustration J STEP 11: Feed the low voltage wires upward through the strain relief on the bottom of the control box (see Illustration J). safety loops, card readers, etc. ) are to be added during this installation, do not tighten the strain relief screw against the wires until the accessories have been connected. When all accessories have been connected, fully tighten the strain relief screw against the wires. Strain Relief Screw + BATT ­ PWR. SW. STATUS AUTO CLOSE INERTIA OBSTRUCT SENS. LEARN OPN EDG CLS EDG GRN ORG BLU WHT B RG OPN EDG CLS EDG RED BLK ORG BLU GRN BLK ORG BLU GRN RED SOLAR 18VAC ­ + ~~ SECOND FIRST OPERAT OR OR OPERAT ALARM ACCESS ORY RCVR POWER IN Low Voltage Wire from AC Transformer Operator Power Cable PVC Conduit 18 INSTALLATION OF THE GTO TRANSFORMER CONT. STEP 12: Illustration K Strip 3/16" off the ends of the low voltage wire and twist tightly. These wire ends will be attached to the control board at the 18VAC terminals located on the POWER IN terminal block (see Illustration L). Wire sheathing should not come in contact with terminals, however, it should not be stripped so far that wires can come in contact with one another (see Illustration K). Insert the other transformer wire into the remaining 1 8 VAC t e r m i n a l ( s e e illustration L). Transformer wires can be connected to the 18VAC terminals regardless of color. A dab of household petroleum jelly on each wire end will help prevent corrosion. The ACCESSORY terminal block provides the connection point for safety loops, wands, push buttons, intercoms, card readers, etc. See page 27 for more information about connecting accessories. Correct Wrong Wrong Wire Terminal Block Wire Terminal Block Wire Terminal Block BLU RED BLK POWER IN FIRST OPERATOR SECOND OPER RED BLACK Power Cable from First Operator Low Voltage Wire from AC Transformer SURGE PROTECTOR Transformer HINT: Keep a few mothballs in the control box to discourage insects from entering it and damaging the control board. STEP 13: Plug the transformer into the electrical outlet. NOTE: Use of a surge protector is strongly recommended. 19 RE 18VAC SOLAR ~~­ + CLS EDG ORG GRN OPN EDG CONTROL BOARD SETTINGS DIP SWITCHES The four DIP switches on the control board match the operator with the type of gate on which it is mounted. Prior to packaging, the GTO/PRO SL-1000 and SL-2000 series control board was configured for a single slide gate that opens right to left. If your gate type matches this configuration, you DO NOT need to adjust the DIP switches. NOTE: The direction a gate opens is determined by standing inside the property and facing toward the gate. NOTE: To change the DIP switch settings, you must turn the control box power switch OFF; move the switch; then turn the power back ON. PULL/PUSH: Set to PULL for slide gates that open RIGHT to LEFT [factory setting]; PUSH for slide gates that open LEFT to RIGHT. PULL/PUSH SNGL/DUAL SEQ1 SNGL/DUAL: Set to SNGL for a single gate leaf [factory setting]; SEQ2 DUAL for dual gate leaves. See Setting the Control Board for Dual Gate Operator Installation on page 37 for more information. See Setting the Control Board for Dual Gate Operator Installation on page 37 for more information (the factory setting is OFF). ON DIP switches OBSTRUCT SENS. 1234 MIN MAX LEARN LOSE AUTOC 60 ­ W. S STATUS OFF 120 + BATT INERTIA MAX MIN UCT OBSTRS. [. . . ] Available in 1000' rolls or special lengths. 11" Push to Open Bracket (FM148) Required when Mighty Mule® 500/502 gate opener(s) must push the gate open, such as on a sloping driveway or where space prevents gate(s) from opening inward (pulled open). Order two PTO brackets for conversion of a dual swing gate installation. Column Mount Lock Receiver (433IH) For mounting the Automatic Gate Lock on brick columns, walls, or for other applications with limited space between gate and post. Replacement Transformer (RB570) Standard 18 volt AC transformer for maintaining the battery included with the Mighty Mule® gate opener. This is the only transformer approved for use with all UL325 Mighty Mule® gate opener systems. HED UNIV DOL REC ERS MODEL EIVER AL F 294 Garage Door Receiver (RB709) The Garage Door Receiver allows you to use the same Mighty Mule® entry transmitter (see Dual and Triple Transmitters) to operate your gate opener and your garage door opener. #41 Slide Gate Chain (RB207) The #41 chain (32' only) is used with the GTO/PRO SL-1000/1200 and SL-2000/22000 DC Slide Gate Operators. If you have a question about any special order item, just call 1-800-543-GATE! The contents of all material available on this installation manual are copyrighted by GTO, Inc. [. . . ]