User manual GRUNDIG WT-AV 1

[. . . ] With the radio transmission system WT-AV 1, you can transmit picture and sound signals from devices which are connected to your television in your living room to an LCD screen or a second television set up, for example, in another room. The device which provides the signals can be, for example, a DVD player, a satellite receiver or a video recorder. Transmitting television signals With the remote control of the device putting out the signals (e. g. For the transmission of remote control signals the infra-red signals of the remote control are transformed into radio signals in the receiver. The transmitter transforms the radio signals back into infra-red signals and transmits them via the infra-red module to the appropriate device, which is also used for the transmission of picture and sound signals. [. . . ] The antenna must be positioned upright in order to function properly. 2 3 Display ­ on the front. R-AUDIO-L OUT VIDEO OUT CH Audio signal output for the audio signals of the device being used. The switch for the selected channel must be set to » DIP ON«. ON/OFF switch. 4 5 6 7 8 DC 9V@ G 16 CONNECTION ______________________________________ Connecting the WT-AV 1 Transmitter CH 8 Xenaro ANT IR R · AUDIO · L IN VIDEO IN I 2 DIP 3 ON 4 3 CH I 2 3 4 DC 9V DIP ON 4 5 2 6 7 1 Note: Use the cinch/EURO-AV cable labelled "for Transmitter". 1 Insert the EURO-AV plug of the cable in the EURO-AV socket of the signal source (e. g. 2 Insert the cinch plug of the cable in the cinch socket of the transmitter. ­ Yellow ­ video signal, red ­ audio signal right, white ­ audio signal left. 3 On the channel switch » CH« select a transmission channel by sliding a switch into the » DIP ON« position. 4 Insert the jack plug of the infra-red module into the » IR« socket. I 2 DIP 3 ON 4 5 Remove the protective film of the adhesive tape from the infra-red receiver and attach the infra-red receiver to the infra-red sensor of the signal source (e. g. Note: For the correct position of the infra-red sensor of the signal source, see the operating instructions for the signal source you are using. When attaching the infra-red receiver, make sure that the infra-red sensor of the signal source is not completely covered. This might make direct operation of the device via remote control impossible. 6 Insert the mains adapter plug into the » DC 9V@« socket. 8 Position the antenna upright. 17 ENGLISH CONNECTION ________________________________________ Connecting the WT-AV 1 Receiver to the TV CH 6 I 2 DIP 3 ON 4 3 ANT R · AUDIO · L OUT VIDEO OUT I CH 2 3 4 DC 9V DIP ON 2 4 5 EURO-AV 1 3 2 1 4 7 5 8 0 6 9 Note: Use the cinch/EURO-AV cable labelled "for Receiver". 1 Insert the EURO-AV plug of the cable in the EURO-AV socket on the television set. 2 Insert the cinch plug of the cable in the cinch socket of the receiver. ­ Yellow ­ video signal, red ­ audio signal right, white ­ audio signal left. 3 On the channel switch » CH« select a transmission channel by sliding a switch into the » DIP ON« position. The other switches must remain in the upper position. I 2 DIP 3 ON 4 Note: Then transmission channel set must be the same as that which was set for the transmitter. 4 Insert the mains adapter plug into the » DC 9V@« socket. [. . . ] These products fulfil the European directives 89/336/EEC and 73/23/EEC. This device conforms to the safety regulation DIN EN 60065 (VDE 0860) and thus the international safety regulation IEC 60065. Gebouw Amstelveste Joan Muyskenweg 22 NL-1096 CJ Amsterdam +31/20-5 68 15 68 GRUNDIG ITALIANA S. P. A. Trener, 8 I-38100 Trento +39/4 61-89 31 11 DECLARATION OF CONFORMITY GRUNDIG AG Beuthener Str. [. . . ]