User manual GRUNDIG WIRELESS-SET 864

[. . . ] COLOR TELEVISION WIRELESS SOUND TRANSMITTER WST 864 29120-269. 0200 ENGLISH CONTENTS __________________________________________________________________________ 3 4 5 6 Scope of delivery Safety The Wireless Sound Transmitter Setting-up Setting up in shelf unit Mounting on the wall 9 Connecting and setting Connecting transmitter Setting transmission channel 10 Starting Switching on and operation Notes on operation and possible interference 11 Information Technical data Rectifying malfunctions 2 SCOPE OF DELIVERY ___________________________________________________ 1 One TU 864 transmitter unit 2 Two RU 864 receiver units, installed 3 Two rear panels with connecting cable (3 m) for wall mounting 4 Operating instructions 5 Two installation angles 6 One cinch cable 7 One 14 Volt plug power supply 1 SURROUND 7 1 14V 6 5 4 7 ······· 5 3 COLOR TELEVISION WIRELESS SOUND TRANSMITTER WST 864 2 3 ENGLISH 3 SAFETY ___________________________________________________________________________________ Krieg am Golf To ensure that this high-quality and user-friendly WIRELESS SOUND TRANSMITTER gives you lasting satisfaction and enjoyment, it is very important that the following points are observed when setting up the appliances. The sound system is designed for transmitting and receiving sound signals. Make sure that fluids or objects do not come into contact with the inside of the appliances (danger of short circuiting). [. . . ] To do so, press latch on the top left of the cover, fold cover to the front and them pull away upwards. 1. 3. 6 Press down terminal lever, pull off speaker cable and take off rear speaker panel. 2. 7 Put up receiver unit and connect speaker cable to terminals of the receiver unit. ­ Insert the speaker » ­ « wire into the black (­) terminal, the speaker cable »+« wire (marked or coloured wire) into the red terminal. 8 Place bottom part of cover into bottom part of receiver unit and push down at the top until it snaps on. ­ Pay attention to location of cable. 9 Insert mains plug into socket. 8 CONNECTING AND SETTING ______________________________ Connecting transmitter 1 Connect the »SURROUND« cinch socket on the TV set with the SURROUND 7 ······· 5 3 1 14V »SURROUND« cinch sockets on the transmitter using the cinch cable provided. 2 Insert the plug power supply socket into the »14V« socket. To the »SURROUND« socket on the TV set 3 Insert plug power supply into the mains socket. Note: The transmitter should be set up near to the TV set in such a way that a clear signal path is not blocked by any obstacle between itself and the speakers and receivers. Setting transmission channel The slide switch on the transmitter and on both receivers is for setting the transmission channel. 7 channels can be selected. 1 Select the same channel using the »CHANNEL« slide switch on the transmitMADE FOR GRUNDIG IN THAILAND CHANNEL 1 3 5 7 ter and on both receivers. from another appliance which is transmitting on the same frequency), please select another transmission channel for the transmitter and both receivers. NF-VERSTÄRKER POWER AMPLIFIER 230V~ 50/60Hz RU 864 ejn ENGLISH 9 STARTING_____________________________________________________________________________ Switching on and operation 1 Switch on both receivers by using the »POWER« switch. ­ The displays illuminate red. 2 Switch on your television set. ON OFF 3 Activate the »Dolby Surround Prologic« (see the operating manual for your TV set) function in the sound menu for your television set. Notes: The transmitter will be automatically switched on if the TV programme or the AUDIO/VIDEO playback is transmitted with Dolby Surround Prologic. The sound signal of the TV set is transmitted to the receivers via the transmitter without use of a wire and the receivers are ready for operation. If a sound signal is not transmitted, the transmitter and both receivers will switch off automatically (approx. ­ The display illuminates red. Notes on operation and possible interference Your WIRELESS SOUND TRANSMITTER is equipped with an HF system which enables the transmission and reception of audio signals without additional cable. International and national regulations limit the HF transmission power to avert radio interference signals which could, for example, come from your neighbors. If the distance to the transmitter is greater, the signal is too weak to be received. Under certain circumstances, persons, walls or other surfaces can reflect the radio signals. Reflected signals mixed with direct (non-reflected) signals can cause signal disturbance, called multipath reception. [. . . ] Radio interference caused by another appliance. Connect the appliances to the mains supply. Connect the »SURROUND« sockets for the transmitter to the TV set using a cinch cable. Select another transmission channel for the transmitter and both receiver units. 12 Grundig AG · Kurgartenstraße 37 · D-90762 Fürth · http://www. grundig. de [. . . ]