User manual GRUNDIG SCC 1500 VD

[. . . ] Aerial Extending the aerial cable to the rear of the car can, for example, impair signal reception. Switching On/Off ­ with the ignition/starter switch You can use the car's ignition/starter switch to switch the radio on and off after it has been switched on with the OI/VOLUME-multi-function control (see supply voltages / A4 +12 V stand by voltage, page 8). ­ on the car radio You can use the OI/VOLUME-multi-function control to switch the radio on and off when the car radio ­ is turned on with the ignition/starter switch or ­ is not connected to the ignition/starter switch. Models/Colour Variants This user manual provides the description for the models SCC 1500 VD, SCC 1501 and SCC 1502 VD. [. . . ] Only SCC 1500 VD and SCC 1502 VD: Only store stations with traffic announcements if >VF< is in the display. Calling up If the U= range is not yet selected: Repeatedly press briefly the fi FM button until U = appears in the display. If you do not wish to take advantage of the Autostore function, you can also manually assign the memory positions of the U= range: Refer to "Selecting a Range" "Tuning to Radio Stations" "Storing Radio Stations" FM AM Only SCC 1500 VD: VF Memory position No c x "­" 1 6 4 Radio Selecting a Range U range VHF 87. 5 - 108 MHz In order to increase the number of memory positions in the U range, your unit is provided with two U ranges: U­ and U= Switching between the U ranges is effected by the fi FM button (stepping button). Only SCC 1501: M range MW 531 - 1602 kHz Press % AM button repeatedly until M appears in the display. L range LW 153 - 279 kHz Press % AM button repeatedly until L appears in the display. Tuning to Radio Stations Automatic search Beforehand: "Selecting a range" U­ or U= Only SCC 1500 VD and SCC 1502 VD: Only store stations with traffic announcements if >VF< is in the display. Briefly press x or c button: to higher frequencies, to lower frequencies. Automatic switching of the search sensitivity (2-stage) c x Immediately the highest search sensitivity: Press the x or c button until >DX< appears in the display. The station search will stop at all receivable stations (local and distant reception). Tuning to Radio Stations Manually Beforehand: "Selecting a range" Switching from automatic search to manual: Press the x or c button until >MAN< appears in the display. Briefly press the x or c button: ­ step-by-step frequency change; Press the x or c button a longer time: ­ fast frequency change; c x GB Briefly press the x or c button: The search stops . . . ­ on the first search run (over the entire frequency range) only on stations which are very well received (local reception), ­ on the second search run on all receivable stations (local and distant reception). If you wish to listen to a different station, press the x or c button once again. 60 seconds as otherwise the search sensitivity would be the same as on the first search run. to higher frequencies, to lower frequencies. 5 Radio Only in the U range ­ The display indicates the frequency in tuning steps of 0. 1 MHz. ­ By briefly pressing the c or x button, the frequency is changed in tuning steps of 0. 05 MHz. So that the frequency indicated in the display corresponds with the frequency tuned to, proceed as follows: After the indication in the display has jumped to the next frequency value when pressing the x button, you must press this button once again so that the frequency indication corresponds to the frequency tuned to. Only SCC 1501: Only in M and L ranges The frequency will change in 9 kHz tuning steps if you press the c or x button briefly (search rocker button). Switching from manual to search: By pressing the either button (except the search button) or automatically after 60 seconds. Storing Stations You can store in memory every station you hear by pressing the station memory position buttons fi 1 to % 6. Beforehand: "Selecting a range" "Tuning to radio stations" Selecting a memory position: Select, for example, the station button fi 1 until the station tuned to is heard again after a brief silence. [. . . ] When removing the control unit with the radio switched on, the radio remains on!Switch the car radio off with the ignition switch or with the multi-function control knob (power consumption). If the flashing SECURITY display disturbs you when driving, you must refit the control panel. Fitting the Control Panel First insert the control panel into the latches at the left in the instrument cut-out. [. . . ]