User manual GRASS VALLEY JUPITER CONTROL SYSTEM RELEASE NOTES V7.9.0

[. . . ] JUPITER CONTROL SYSTEM Release Notes Software Version 7. 9. 0 071827513 NOVEMBER 2010 Affiliate with the N. V. KEMA in The Netherlands CERTIFICATE Certificate Number: 510040. 001 The Quality System of: Thomson Inc, and it's wordwide Grass Valley division affiliates DBA GRASS VALLEY Headquarters 400 Providence Mine Rd Nevada City, CA 95959 United States Kapittelweg 10 4827 HG Breda The Nederlands Rue du Clos Courtel CS 31719 35517 Cesson-Sevigné Cedex France 40 Rue de Bray 2 Rue des Landelles 35510 Cesson Sevigné France Carl-Benz-Strasse 6-8 67105 Schifferstadt Germany 15655 SW Greystone Ct. Beaverton, OR 97006 United States 7140 Baymeadows Way Ste 101 Jacksonville, FL 32256 United States 1 rue de l'Hautil Z. I. des Boutries BP 150 78702 Conflans-Sainte Honorine Cedex France Spinnereistrasse 5 CH-5300 Turgi Switzerland 10 Presidential Way Suite 300 Woburn, MA 01801 United States 2300 So. [. . . ] Ensure that the configuration set that is opened is the one that you want to change. Follow these steps to enter or modify the Serial Protocol table: 1. Select the Serial Protocol option from the Jupiter menu (Jupiter> Serial Protocol). The Serial Protocol table will then open (Figure 3). 14 JUPITER -- Release Notes Pro-Bel SW-P-08 Protocol Figure 7. Double-click the protocol box that is associated with the Serial port. The Baud rate can be changed by clicking the drop-down list in the Baud rate column. Figure 8. The P8R (SW-P-08 Router Control) Protocol on The Serial Protocol Table Protocol Baud Rate 5. Compile and activate the Configuration set. JUPITER -- Release Notes 15 Version 7. 9. 0 Pro-Bel SW-P-08 Interface Implementation Notes P8R (SW-P-08 Router Control) The P8R (SW-P-08 Router Control) driver will send the following: Table 3. P8R(SW-P-08 Router Control) driver Sent Information Message CONNECT CONNECT_EXT Value 2 (matrix=pLvl/16, level =pLvl%16 input < 1024 output < 1024) 130 (depending on the input and output >= 1024) This P8R (SW-P-08 Router Control) driver will receive the following: Table 4. P8R(SW-P-08 Router Control) driver Received Information Message CONNECTED CONNECTED_EXT 4 132 Value When the P8R (SW-P-08 Router Control) driver is used, the following will occur: · The Commands that are not extended will truncate the Matrix and the Level values to a 4 bit value. The Level value in the PLvl column of the Switcher Description Table is converted into a unique Level value between 0 and 100 (0 - 0x63). The Physical level (PLvl) value is then converted into a Pro-Bel SW-P08 Matrix and Level value. The Pro-Bel SW-P-08 level value is from 0 to 15 and the Pro-Bel SW-P-08 matrix value is from 0 to 6, which is the physical level divided by 16. A Jupiter system TAKE command will send a Pro-Bel CONNECT message, which is confirmed when a CONNECTED message is received immediately following the CONNECT message. The interface will re-send a CONNECT message up to three more times after an error or if the CONNECTED response is not what was expected to confirm the TAKE command. The protocol ACKS all messages that are received correctly even if they are not implemented. · · · · 16 JUPITER -- Release Notes Pro-Bel SW-P-08 Protocol P08 (SW-P-08 Control Panel) The P08 (SW-P-08 Control Panel) driver will receive the following: Table 5. P08 (SW-P-08 Control Panel) Received Information Message CONNECT CONNECT_EXT INTERROGATE INTERROGATE_EXT CONNECTED CONNECTED_EXT Single source name request Single destination name request Single source name extended Single destination name extended 2 130 1 129 4 132 101 103 229 231 Value The P08 (SW-P-08 Control Panel) sends the following: Table 6. P08 (SW-P-08 Control Panel) Sent Information Message TALLY TALLY_EXT CONNECTED CONNECTED_EXT Source name response Destination name response Source name response extended Destination name response extended 3 131 4 132 106 107 234 235 Value When the P08 (SW-P-08 Control Panel) driver is used, the following will occur: · · · The control panel level value is a combination of the Pro-Bel SW-P-08 matrix and level values. The interface ACKS all messages that are received correctly even if they are not implemented. The system responds to a CONNECT message with a CONNECTED message only when the cross point is valid. Unsolicited CONNECTED messages will be sent for confirmed TAKES to outputs in the control panel set. Commands are repeated up to 3 times when a NAK (error) occurs. JUPITER -- Release Notes 17 Version 7. 9. 0 Physical Serial Interface This section describes the pins of the Serial cable. The two Tables (Table 7 and Table 8) describe the configuration. Figure 9. Serial Cable Pin-out G 1 6 071827512_Probell-Serial connections 1 2 3 8 T 4 9 5 G 6 7 8 9 R- R+ T+ T- 2 7 3 4 5 R RS-422/485 (female) RS-232 DTE (male) Table 7. [. . . ] The Preparing to Install screen will then be displayed (Figure 11). Figure 11. Preparing to Install Screen 24 JUPITER -- Release Notes Installing the Jupiter Software Components The Welcome - Remove the program screen will then appear after a few minutes (Figure 12). Figure 12. Setup Status Screen The previous version of the application will then be removed. JUPITER -- Release Notes 25 Version 7. 9. 0 When the removal of the application has been completed, the Maintenance Complete screen will then appear (Figure 14). Figure 14. The InstallShield Wizard application will then close. You can now install the latest version of Jupiter. Installing the Latest Version Note To help ensure any hidden activity is stopped you should restart the computer. Before you begin the installation process, make sure that you close all Jupiter programs on the configuration PC and disable any virus protection programs or firewalls. 26 JUPITER -- Release Notes Installing the Jupiter Software Components Follow these steps to start a new installation Process: 1. [. . . ]