User manual GRACO TURBINE ALTERNATOR 308034
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual GRACO TURBINE ALTERNATOR. We hope that this GRACO TURBINE ALTERNATOR user guide will be useful to you.
Manual abstract: user guide GRACO TURBINE ALTERNATOR308034
Detailed instructions for use are in the User's Guide.
[. . . ] InstructionsParts List
Turbine Alternator Repair Kits
308034F
ENG
For repair of turbine alternator used with PRO Series Electrostatic Spray Guns, with PRO Pulse Electronic Fluid Meter, and with SuperCatt, Xtreme Mixt 185, ProMixt Easy, and ProMixt I Proportioners. For professional use only.
Important Safety Instructions Read all warnings and instructions in this manual. 223688 Bearing Repair Kit
223688
TI1884A
WARNING
FIRE, EXPLOSION, AND ELECTRIC SHOCK HAZARD
Improper grounding, poor air ventilation, open flames, or sparks can cause a hazardous condition and result in a fire, explosion, or electric shock. [. . . ] Test the Coil: Measure the resistance between the two outer terminals of the 3-pin connector (101a). Measure the resistance between each outer terminal of the 3-pin connector and the turbine alternator housing (B). Remove the plastic plug (A).
CAUTION
To avoid demagnetization of the armature (D), never place it in contact with, or in close proximity to, any other armature or other ferromagnetic objects. 217590) if necessary.
2
308034
Turbine Alternator Service
KEY
A B D E G H 1 2 3 101 101a Plug Turbine Alternator Housing Armature O-Ring Turbine Assembly Retaining Ring (Pro Xs only) Bearing Bearing Fan Coil 3-Wire Connector
PRO 3500 / 4500 / 5500, PRO Pulse, and SuperCat, Xtreme Mix 185, ProMix Easy, and ProMix I Proportioners E A B
Exhaust Port
G D 101 2 101a
1
3 E A B PRO Xs Models
H PRO Xs only
NOTE: The items referenced with numbers are included with a kit.
TI15230a
Fig. Remove the bearings (1 & 2) from the package and wipe the excess oil off with a soft cloth. Place the smaller bearing (1) [marked 197906] on the long end of the armature (D), with the machined groove in the bearing facing the armature. Install the fan (3) on the long end of the armature (D), with the machined groove in the fan facing away from the armature. Lightly tap on the end of the armature (D) until the fan is pressed up against the spacing tool and bearing. When properly installed, the bearing (1) should spin freely on the armature shaft. Install the coil assembly (101) over the armature (D), with the 3-wire connector (101a) facing away from the fan (3).
6. Place the larger bearing (2) [marked 197907] on the end of the armature (D), with the machined groove in the bearing (2) facing in toward the armature. NOTE: When installed, the bearing legs must not block the exhaust ports of the turbine alternator housing (B) or the gun will not operate properly. Carefully slide the turbine alternator housing (B) over the turbine assembly (G), aligning the bearing legs between the exhaust ports of the housing. Push the turbine alternator housing onto the turbine assembly until the assembly is seated firmly in the turbine alternator housing. [. . . ] TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you: Phone: 6126236921 or Toll Free: 18003280211 Fax: 6123783505
All written and visual data contained in this document reflects the latest product information available at the time of publication. MM 308034 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. BOX 1441 MINNEAPOLIS, MN 554401441
4
308034
Copyright 1990, Graco Inc. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE GRACO TURBINE ALTERNATOR
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual GRACO TURBINE ALTERNATOR will begin.