User manual GRACO 15H874 REV 9-2010

[. . . ] Open the back pressure regulator and all fluid drain valves in the system, having a waste container ready to catch drainage. Check that pressure gauges on fluid supply and return lines read zero. If gauges do not read zero, determine cause and carefully relieve pressure by VERY SLOWLY loosening a fitting. [. . . ] 2: Slider Cylinder Rebuild Kit 7 311599C 3 Kit Installation Reassembly 1. The joints between the bearings must align with the pin hole (PH) in the slider piston. Install the setscrew (31*). Torque to 30-35 in-lb (3. 4-3. 9 N·m). Install two screws (12) and the cover (32 is shown; use 21 on the motor side). Screw the tie rod locknuts (15*) included in the kit onto the tie rods handtight. Assemble the inlet and outlet manifolds (17) to the lower, using new gaskets (16*). Torque the adapter (42) first, then the nut (43) to 15-20 ft-lb (21-27 N·m). wrench on the flats of the slider piston (9), to keep it from turning when you are tightening the coupling nut (14). Orient the wrench so it is braced against one of the tie rods (3) or the pump stand. Tighten the coupling nut (14) onto the slider piston (9) and torque to 75-80 ft-lb (102-108 N·m). Turn on power and jog the motor to repeat procedure for the other lower. Adjust or repair as necessary before reinstalling in the system. 4 311599C Kit Installation . 21 *8 12 *2 *41 17 18 43 32 42 25a 12 13 PR 31* *16 5 14 7 PH1 9 14 22 *16 4 Torque to 50-60 ft-lb (68-80 N·m). 3: Slider Cylinder Rebuild Kit 7 311599C 5 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco's written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. [. . . ] FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées. Graco Information For the latest information about Graco products, visit www. graco. com. TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor. [. . . ]