User manual GIGAFAST EE410-R

[. . . ] GigaFast EE 410-R Broadband Router User Guide 2 FCC Warning This equipment has been tested and found to comply with the regulations for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his or her expense. CE Mark Warning This is a Class B product. [. . . ] If the WAN Port's Link indicator does not light up then replace the RJ-45 cable that plugged onto WAN's "X" port to the "II" port or from the "II" port to the "X" port at the rear or using a crossover cable to connect on the WAN port to meet the specification need of the xDSL or Cable modem. While the LAN is link up to the computer system, the LAN port's Link/ACT LED will light up. 10 PC NETWORK TCP/IP SETTING The network TCP/IP settings differ based on the computer's operating system (Win95/98/ME/NT/2000) and are as follows. Windows 95/98/ME 1. Click on the "Network neighborhood" icon found on the desktop. Select "Obtain an IP address automatically" on the "IP address" field. 11 5. Select "None" for the "Gateway address" field. 12 Windows 2000 Double click on the "My computer" icon on the desktop. When "My computer" window opens, open the "Control panel" and then open the "Network dialup connection" applet. In the "Local area network status" window, click on "Properties. " 2. In the "Local area network connection" window, first select TCP/IP setting and then select "Properties. " 3. Set both "IP address" and "DNS" to Automatic configuration. 13 Windows NT4. 0 Click on the "Start" button located on the lower left corner of the menu bar. Select "Settings" and then "Control panel. " In the "Control panel" window, select "Network" to enter the TCP/IP setting window. Set "IP address" to "Obtain an IP address automatically. " 2. Set "DNS" to "Disable DNS. " 14 Windows XP Point the cursor and click the right button on the "My Network Place" icon. Set "IP address" to "Obtain an IP address automatically. " 2. Fill up the MAC Address of the network adapter when the DNS server need a certain address with the network adapter, or press the "Clone MAC Address" button to get the manager's PC MAC Address. 19 1-2-2 Fixed IP If the Internet Service Providers assign a fixed IP address, choose this option and enter the assigned IP address, subnet mask, gateway IP and DNS IP addresses for your Broadband Router. 1-2-3 Dial-up xDSL (PPPoE) If connected to the Internet using a Dial-up xDSL (PPPoE) Modem, the ISP will provide a Password and User Name, and then the ISP uses PPPoE. Choose this option and enter the required information, if the ISP provided a Service Name, enter it in the column of the Service Name field, otherwise, leave it blank. The MTU feature specifies the largest packet size permitted for network transmission. Enter the value desired, for most DSL users, it is recommended to use 1492. The Maximum Idle Time feature can control the connection time while user's need to save the cost of connection fee from ISP provider (default time=0, always connect). Click on the Connect-on-demand 20 button to dial up to the ISP when only on demand, while there is a need of connecting to the ISP automatically. 1-2-4 PPTP If connected to the Internet using a (PPTP) xDSL Modem, enter the PPTP Account Name, PPTP Password, Host Name, Service IP Address, Your IP Address, Your Subnet Mask required by your ISP in the appropriate fields. If your ISP has provided you with a Connection ID, enter it in the Connection ID field, otherwise, leave it zeros. The MTU feature specifies the largest packet size permitted for network transmission. [. . . ] These applications cannot work when Network Address Translation (NAT) is enabled. When users send this type of request to your network via the Internet, the Router will forward those requests to the appropriate PC. If you need to run applications that require multiple connections, specify the port normally associated with an application in the "Trigger Port" field, select the protocol type as TCP or UDP, then enter the public ports associated with the trigger port to open them for inbound traffic. 31 TCP (Transmission Control Protocol) - A method (protocol) used along with the Internet Protocol (Internet Protocol) to send data in the form of message units between computers over the Internet. [. . . ]