User manual GIGAFAST EE101-AEX

[. . . ] PCMCIA Fast Ethernet card user's manual PCMCIA 10/100M Fast Ethernet Card User's Manual Rev 2. 0 PCMCIA Fast Ethernet card user's manual Regulatory compliance This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. This equipment also complies with CE EN55022 Class B and VCCI V3 Class B specifications. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] The system will find the setup files and follow the instruction of the setup file to copy drivers. After the drivers were copied, the following screen appears: 26 PCMCIA Fast Ethernet card user's manual Note! If you did not install the Windows ME from your hard drive, Windows will prompt you to input the path to the Windows ME CD-ROM. Follow the instructions on your screen, then click OK to continue. 5. You should reboot your system to finish the installation. 27 PCMCIA Fast Ethernet card user's manual Driver installation for Windows 2000 Follow the steps below to install the Ethernet card drivers for Windows 2000. Insert the Ethernet card into an available PCMCIA slot on your notebook. After Windows 2000 detects the Ethernet card, the Found New Hardware Wizard window appears: 3. A screen appears prompting you to select an installation method: 28 PCMCIA Fast Ethernet card user's manual 4. Select Search for a suitable driver for my device (recommended) and click Next. Ensure that the CD-ROM drives box is checked and insert the driver disc into CD-ROM drive. Click Next to continue. 29 PCMCIA Fast Ethernet card user's manual After the system search the best driver, the following search results window appears: 6. Windows copies files and the following screen appears: 30 PCMCIA Fast Ethernet card user's manual 9. You should reboot the computer to insure a successful installation. 31 PCMCIA Fast Ethernet card user's manual Driver installation for Windows NT 4. 0 This installation procedure assumes that you have installed the network component on your computer. To check whether the network component has been installed, double click the Network icon in the Control Panel. If it has not been installed, refer to the Windows NT 4. 0 installation guide for instructions on installing the component. Insert the Ethernet card into an available PCMCIA slot on your notebook. Double click the Network icon in the Control Panel, and select the Adapters tab as shown in the following screen: 32 PCMCIA Fast Ethernet card user's manual 4. Type "E:\Driver\WinNT40" where "E" is your CD-ROM drive letter. After finding the installation file, the Select OEM Option window is displayed. 33 PCMCIA Fast Ethernet card user's manual 7. A screens appears prompting you to input the IRQ, I/O port address, and connection type: 8. Select the desired resources and connection type. Note! You must select resources that are not being used by another device; otherwise, you will have a system conflict error. In case of a system conflict error, try another setting and continue. 9. You are returned to the Network window. 34 PCMCIA Fast Ethernet card user's manual 10. [. . . ] Follow the instructions on the screen to complete the installation, then reboot the computer to start LANtastic. 49 PCMCIA Fast Ethernet card user's manual Chapter 5 Installation for LINUX This section covers the Ethernet Card driver installation for the Linux environment operating system. Before you install the PCMCIA 10/100 Ethernet card Linux driver, you must first configure the PCMCIA interface in your Linux working environment. System Requirements · · Linux kernel version 2. 0. x or later PCMCIA interface 3. 0. x or later You can get the latest version of the PCMCIA interface package from the one of the following URLs: · · ftp://ftp. tux. org/util/pcmcia/ ftp://sourceforge. org/pcmcia/ After downloading the PCMCIA interface package, refer to the PCMCIA-HOWTO file for installation instructions. 50 PCMCIA Fast Ethernet card user's manual Installing the driver for Linux Follow these instructions to install the driver for the Linux operating system: 1. Copy the driver code from the Installation disc using the following syntax: mount -rt iso9660 /dev/hdc /cdrom cp /cdrom/driver/Linux/in0100-af-v1. 51. tgz /tmp cd /tmp gzip -cd in0100-af-v1. 51. tgz | tar xvf - 3. Generate the driver using the following syntax: cd in0100-af-v1. 51 make all If the path of your PCMCIA source is not "/usr/src/pcmcia", you need to modify the "PCMCIASRC" variable of the "Makefile" file. If the kernel version is not 2. 2. 6, you need to modify the KERN_VER variable in makefile. 4. [. . . ]