User manual GIGABYTE U24F

[. . . ] Prior to installation, carefully read the user's manual and follow these procedures: • Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. • Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components. • When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely. • When handling the motherboard, avoid touching any metal leads or connectors. [. . . ] • Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user. • If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician. -6- Hardware Installation 1-2 Product Specifications CPU  Supports single Intel® D525 processor  Supports 1. 8GHz Chipset Memory  Intel® ICH8M  1 x SO-DIMM slot support DDR3 800  Support up 2GB     Realtek® ALC269 codec High Definition Audio 2 channel 1 x Realtek® RTL 8111Ed supports 10/100/1000 Mbps Audio LAN Expansion Slots  1 x mini PCI Express x1 slot Onboard  Build in Intel® ICH8M chipset Graphics Storage Interface  2 x SATA 3Gb/s connectors  1 x 7 pin & 15 pin SATA connector USB  Up to 10 USB 2. 0/1. 1 ports (4 on the back panel, 6 via the USB brackets connected to the internal USB headers) Internal  1 x 4 pin ATX 12V power connector Connectors  2 x SATA 3Gb/s connectors  2 x SATA power connectors  1 x 7 pin & 15 pin SATA connector  1 x CPU fan header  1 x System fan header  4 x COM power select connector  1 x front panel header  1 x audio header  3 x USB 2. 0 headers  1 x VGA header  1 x LVDS connector Back Panel  1 x DC-in (12V) connector Connector  4 x USB 2. 0 ports  2 x RJ-45 port  1 x VGA port  1 x COM ports  1 x Parallel port  1 x RJ-11 port  1 x Audio jack  1 x PS/2 connector Hardware Installation -7- Form Factor  Mini ITX Form Factor; 6. 75 inch x 6. 75 inch * GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice. -8- Hardware Installation 1-3 Installing the Memory Read the following guidelines before you begin to install the memory: • Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used. (Go to GIGABYTE's website for the latest supported memory speeds and memory modules. ) • Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage. If you are unable to insert the memory, switch the direction. 1-3-1 Installing a Memory Before installing a memory module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. Align the memory with the DIMM module and insert the DIMM memory module into the DIM slot. Reverse the installation steps when you wish to remove the DIMM module. 1 2 Hardware Installation -9- 1-4 Back Panel Connectors b d b f a c e c g h i (a). RJ-45 LAN Port The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. USB 2. 0/1. 1 Port The USB port supports the USB 2. 0/1. 1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc. (d). Serial Port Connects to serial-based mouse or data processing devices. (e). For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis. SYS_FAN 1 SYS_FAN (System Fan): Pin No. 1 2 3 Definition GND +12V / Speed Control Sense SYS_FAN1 1 CPU_FAN (CPU Fan): Pin No. 1 2 3 Definition GND +12V / Speed Control Sense Speed Control CPU_FAN CPU_FAN 4 • Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Do not place a jumper cap on the headers. 6) VGA2 (VGA Cable Header) Pin No. Definition 1 2 3 1 2 9 10 V-SYNC H-SYNC GND GND RED GND GREEN DDC Clock BLUE DDC Data 4 5 6 7 8 9 10 - 16 - Hardware Installation 7) KB_MS2 (PS/2 Cable Header) Pin No. 1 2 3 4 5 6 7 8 9 10 Pin Definition Stand-by LED Signal Power LED Signal Power Switch Ground LAN Act LED Signal LAN Act LED 5V HDD LED VCC 5V Reset Button Ground The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly. Hardware Installation - 20 - 16/17/18) F_USB3/F_USB2/F_USB1 (USB Headers) The headers conform to USB 2. 0/1. 1 specification. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer. 1 2 9 F_USB1 F_USB2 10 F_USB3 F_USB1/F_USB2 F_USB3 Pin No. 1 2 3 4 5 6 7 8 9 10 Definition Power (5V) Power (5V) USB DXUSB DYUSB DX+ USB DY+ GND GND No Pin NC Pin No. [. . . ] • Used batteries must be handled in accordance with local environmental regulations. 20/21/22/23/28) COM6/COM3/COM5/COM1/COM4 (Serial Port Header) The COM header can provide one serial port via an optional COM port cable. For purchasing the optional COM port cable, please contact the local dealer. COM4 1 2 9 10 COM1 COM1 COM5 COM3 COM6 1 9 COM3 COM5 COM6 Pin No. 1 2 3 4 5 6 7 8 9 10 Definition DCD DSR RXD RTS TXD CTS DTR RI/+5V/+12V GND RI/+5V/+12V 2 COM4 10 - 22 - Hardware Installation 24/25/26/27) JCOM6/JCOM3/JCOM5/JCOM1 (5V/12V/RI for Serial Port Option Header) 2 JCOMS1 JCOMS5 JCOMS3 JCOMS6 6 1-2 Close: 5V (Power COM) 1 2 5 6 3-4 Close: RI (STAND COM) 1 2 5 6 5-6 Close: 12V (Power COM) 1 5 29) LCDPWR_CON (LCD Power ON/OFF Jumper) Open: Power off. Short: Power On. - 23 - Hardware Installation 30) BKLTEN_CON (Back light Inverter Enable/Disable Jumper) Open: Disable Back light Inverter. [. . . ]