User manual GIGABYTE P25K

[. . . ] No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without Gigabyte's prior written permission. Specifications and features are subject to change without prior notice. Product Manual Classification In order to assist in the use of this product, Gigabyte has categorized the user manual in the following:  For detailed product information and specifications, please carefully read the "Product User Manual".  For detailed information related to Gigabyte's unique features, please go to "Technology Guide" section on Gigabyte's website to read or download the information you need. For more product details, please click onto Gigabyte's website at www. gigabyte. com. tw P25K Motherboard Table of Content Item Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you use a power supply that provides a 24-pin ATX power connector, please remove the small cover on the power connector on the motherboard before plugging in the power cord; otherwise, please do not remove it. 4 2 Pin No. 1 2 Definition GND GND +12V +12V 3 1 3 4 14 P25K Motherboard 1 13 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 Definition 3. 3V 3. 3V GND +5V GND +5V GND Power Good 5V SB(stand by +5V) +12V +12V(Only for 24-pin ATX) 3. 3V(Only for 24-pin ATX) Pin No. 13 14 15 16 17 18 19 20 21 22 23 24 Definition 3. 3V -12V GND PS_ON(soft On/Off) GND GND GND -5V +5V +5V +5V (Only for 24-pin ATX) GND(Only for 24-pin ATX) 12 24 3/ 4 ) SATAII 1/2 (Serial ATA cable connectors) SATA 3Gb/s can provide up to 300MB/s stransfer rate. Please refer to the BIOS setting for the SATA 3Gb/s and install the proper driver in order to work properly. 1 1 7 Pin No. 1 2 3 4 5 6 7 7 Definition GND TXP TXN GND RXN RXP GND 15 P25K Motherboard 5/6/7 ) COMB/COMC/COMD (Serial cable connectors) COMB COMC COMD COMB 2 1 10 9 COMC 1 2 COMD 1 2 9 10 Pin No. 1 2 3 4 5 6 7 8 9 10 Definition NDCDBNRXDB NTXDBNDTRBGND NDSRBNRTSBNCTSBNRIBNC Pin No. 1 2 3 4 5 6 7 8 9 10 Definition NDCD3NRXD3 NTXD3NDTR3GND NDSR3NRTS3NCTS3NRI3_CNC Pin No. Remember to connect the CPU/system fan cable to the CPU_FAN/SYS_FAN connector to prevent CPU damage or system hanging caused by overheating. 1 Pin No. 1 2 3 4 Definition GND 12V Sense Control CPU_FAN SYS_FAN 19 Connector Introduction 15 ) F_Panel (2X5 Pins Front Panel connector) Please connect the power LED, PC speaker, reset switch and power switch of your chassis front panel to the F_PANEL connector according to the pin assignment above. 2 10 1 9 Pin No. 10. Signal Name HD+ MSG+ HDMSGRESPW+ RES+ PWACTACT+ Description Hard Disk LED Signal anode (+) Message LED Signal anode (+) Hard Disk LED Signal cathode(-) Message LED Signal cathode(-) Reset Button anode (+) Power Button Signal cathode(-) Reset Button cathode(-) Power Button Signal anode (+) LAN active LED Signal cathode(-) LAN active LED Signal anode (+) 20 P25K Motherboard 16 ) BATTERY If you want to erase CMOS. . . (Default setting) Disable the device. IDE Disabled Primary IDE Master, Slave The category identifies Serial ATA and IDE types of hard disk that are installed in the computer. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. Hard drive information should be labeled on the outside device casing. TYPE Not Installed: No device is installed. 27 P25K Motherboard Auto: Set parameters automatically. (Default setting) CD-ROM: Use for ATAPI CD-ROM drives or double click [Auto] to set all HDD parameters automatically. LBA/Large Mode Configure the device type in the specific IDE channel support LBA Mode. (Default setting) Block (Multi-Sector Transfer) Configure the information of Multi-Sector Transfer Mode. Disabled: The data transfer from and to the device occurs one sector at a time. Auto: The data transfer from and to the device occurs multiple sectors at a time if the device supports it. (Default setting) PIO Mode This feature allows you to set the PIO (Programmed Input/Output) mode for the two IDE devices (Master and Slave drives) attached to that particular IDE channel. [. . . ] (Default setting) Normal operation during system boot. BootupNumLock This option allows user to select power-on state for NumLock. (Default setting) Disable this function. Wait for ‘F1’ If Error Hit ‘DEL’ Message Display Boot Device Priority This field determines which type of device the system attempt to boot from after BIOS Post completed. If the first device is not a bootable device, the system will seek for next available device. 42 P25K Motherboard Security About This Section: Security In this section, user can set either supervisor or user passwords, or both for different level of password securities. In addition, user also can set the virus protection for boot sector. Main Advanced PCIPnP Boot BIOS SETUP UTILITY Security Chipset Exit Security Settings Supervisor Password User Password Change Supervisor Password User Access Level Change User Password Clear User Password Password Check : Not Installed : Not Installed [Full Access] [Setup]   +Tab F1 F10 ESC v02. 61 (C) Copyright 1985-2006, American Megatrends, Inc. [. . . ]