User manual GIGABYTE MP30-AR0

[. . . ] • The motherboard image is for reference only. -4- MP30-AR0 Motherboard Layout 1 2 3 4 5 6 7 27 8 28 29 30 32 9 33 34 11 35 13 12 10 26 257 24 23 22 312 21 14 20 19 18 17 16 15 -5- Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 LED_STA USB2_MLAN VGA1_COM1 SFP+_1_2 LAN1_2 SW_PWR SW_ID CPU_FAN DIMM_P0_A0 DIMM_P0_A1 DIMM_P0_B0 DIMM_P0_B1 CPU0 P12V_AUX1 ATX1 SYS_FAN1 FP_1 SYS_FAN2 PMBUS CLR_CMOS SYS_FAN3 BP_1 CASE_OPEN IPMB SYS_FAN4 SATA_DOM0 SATA0/1/2/3 PCIE_2 BAT PCIE_1 LED_BMC DIMM_P0_C0 DIMM_P0_C1 DIMM_P0_D0 DIMM_P0_D1 Code Description System status LED BMC Management LAN port (top)/USB 2. 0 ports (bottom) Serial port (top)/VGA port (bottom) 10G Fiber LAN ports LAN ports Power button/LED ID switch button/LED CPU fan connector Channel 1 slot 0 Channel 1 slot 1 Channel 2 slot 0 Channel 2 slot 1 ARM CPU 4 pin power connector 24 pin main power connector System fan connector#1 Front panel header (for Server system) System fan connector#2 PMBus header Clear CMOS jumper System fan connector#3 HDD back plane board header Case open intrusion alert header IPMB connector System fan connector#4 SATA port 3 DOM support jumper SATA3 6Gb/s connectors PCI Express x16 slot Battery socket PCI Express x16 slot BMC firmware readiness LED Channel 3 slot 0 Channel 3 slot 1 Channel 4 slot 0 Channel 4 slot 1 CAUTION!If a SATA type hard drive is connected to the motherboard, please ensure the jumper is closed and set to 2-3 pins (Default setting), in order to reduce any risk of hard disk damage. -6- Block Diagram -7- Chapter 1 Hardware Installation 1-1 Installation Precautions The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). [. . . ] 1. Four Channel mode cannot be enabled if only one DDR3 memory module is installed. 2. When enabling Four Channel mode with two or four memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used for optimum performance. Hardware Installation - 10 - DIMM_P0_B1 DIMM_P0_B0 DIMM_P0_A1 DIMM_P0_A0 1-3-2 Installing a Memory Before installing a memory module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. Installation Step: Step 1. Insert the DIMM memory module vertically into the DIMM slot, and push it down. Step 2. Close the plastic clip at both edges of the DIMM slots to lock the DIMM module. Note: For dual-channel operation, DIMMs must be installed in matched pairs. Step 3. Reverse the installation steps when you wish to remove the DIMM module. 2 1 2 - 11 - Hardware Installation 1-4 Back Panel Connectors Serial Port Video Port Connects to serial-based mouse or data processing devices. The video in port allows connect to video in, which can also apply to video loop thru function. RJ-45 LAN Ports (Gigabit Ethernet LAN Ports) System Status LED Color Status On Green Blink The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs. Description System is operating normally. Degrade condition, may indicates the following: • CPU failure • DIMM killed Critical condition, may indicates the following: • Power module failure • System fan failure • Power supply voltage issue • System temperature/voltage issue Non-critical condition, may indicates the following: • Redundant power module failure • Temperature and voltage issue • Chassis intrusion System is not ready. May indicate the following: • POST error • NMI error • Processor or terminator missing On Amber Blink N/A Off USB 2. 0 Port The USB port supports the USB 2. 0 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc. KVM Server Management 10/100/1000 MbpsLAN Port (Dedicated LAN Port) The LAN port provides Internet connection with data transfer speeds of 10/100/1000Mbps. This port is the decated LAN port for server management. SFP+ LAN Port The SFP+ LAN port provides Internet connection at up to 10 Gbps data rate. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. Connect the power supply cable to the power connector in the correct orientation. If the 12V power connector is not connected, the computer will not start. [. . . ] • If the SATA DOM power is supplied by external power, set the jumper to pin 2-3. • If a SATA type hard drive is connected to the motherboard, please ensure the jumper is closed and set to 2-3 pins (Default setting), in order to reduce any risk of hard disk damage. Please refer to the pin definition table in the following. 1 Pin No. 1 2 3 Definition P5V SATA3 Pin7 GND 17) CLR_CMOS (Clearing CMOS Jumper) Use this jumper to clear the CMOS values (e. g. [. . . ]