User manual GIGABYTE IF 233

[. . . ] 9 Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installing the Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Installing a Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1-3-1 Back Panel Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Internal Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Note the positive and negative pins before connecting the cables. 2 1 10 9 Pin No. 1 2 3 4 5 6 7 8 9 10 Signal Name HD+ MPD+ HD- GND GND PW+ RST+ GND NC NC Definition Hard Disk LED Signal anode (+) Power LED Signal anode (+) Hard Disk LED Signal cathode(-) Ground Ground Power Button anode (+) Reset Button Ground No connect No Pin The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly. - 25 Hardware Installation 23) F_USB1 (USB Header) The headers conform to USB 2. 0/1. 1 specification. Each USB header can provide two USB ports via an optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer. 2 1 10 9 Pin No. 1 2 3 4 5 6 7 8 9 10 Definition Power (5V) Power (5V) -FUSBP2 -FUSBP3 +FUSBP2 +FUSBP3 GND GND GND GND 24) GPIO_CNT (GPIO connector) 11 12 1 2 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 Definition SOGPO_1 SOGPI_1 SOGPO_2 SOGPI_2 SOGPO_3 SOGPI_3 SOGPO_4 SOGPI_4 SMCLK_N SMDATA_N +5V GND Hardware Installation - 26 - 25) F_AUDIO (Front Panel Audio Header) The front panel audio header supports Intel High Definition audio (HD) and AC'97 audio. Make sure the wire assignments of the module connector match the pin assignments of the motherboard header. Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it. Pin No. 1 2 3 4 5 6 7 8 9 10 Definition MIC_L GND MIC_R -ACZ_DET HPOUT_R GND FAUDIO_J NC HPOUT_L GND 2 1 10 9 26) SPK_OUT (Audio Amplifier Connector) 1 4 Pin No. 1 2 3 4 Definition OUT_R+ OUT_ROUT_LOUT_L+ - 27 - Hardware Installation 27/28) CPU_FAN/SYS_FAN (CPU Fan/System Fan Headers) The motherboard has one 4-pin CPU fan header (CPU_FAN), and one 4-pin (SYS_FAN) system fan headers. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The motherboard supports CPU fan speed control, which requires the use of a CPU fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis. CPU_FAN SYS_FAN 1 4 4 SYS_FAN 1 CPU_FAN Pin No. 1 2 3 4 Definition GND +12V Sense Speed Control • Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. (Pressing <Esc> can also carry out this task. ) - 31 - BIOS Setup 2-1 The Main Menu Once you enter the BIOS Setup program, the Main Menu (as shown below) appears on the screen. Use arrow keys to move among the items and press <Enter> to accept or enter other sub-menu. Main Menu Help The on-screen description of a highlighted setup option is displayed on the bottom line of the Main Menu. Submenu Help While in a submenu, press <F1> to display a help screen (General Help) of function keys available for the menu. Help for each item is in the Item Help block on the right side of the submenu. • When the system is not stable as usual, select the Restore Defaults item to set your system to its defaults. • The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version. BIOS Setup - 32 - BIOS Information Project Name BIOS Version Display name of the project. Display version number of the BIOS. BIOS Build Date and Time LAN1/2 MAC Address Memory Information Total Memory TXE FW Version System Date Displays the date and time when the BIOS setup utility was created. Displays the LAN1 and LAN2 MAC address information. Display the total memory size of the installed memory. Set the system time following the hour-minute- second format. System Time - 33 - BIOS Setup 2-2 Advanced Menu The Advanced menu display submenu options for configuring the function of various hardware components. Select a submenu item, then press Enter to access the related submenu screen. BIOS Setup - 34 - 2-2-1 Hardware Monitor Press Enter to view the Hardware Monitor screen which displays a real-time record of the CPU/system temperature, and fan speed, Items on this window are non-configurable. PC Health Status CPU/System SMART FAN Function Enable CPU/System Fan Stop Warning function. [. . . ] Display the Serial Port 4 base I/O addressand IRQ. Serial Port 5 Configuration Use This Device Logical Device Settings When enabled allows you to configure the serial port 5 settings. Display the Serial Port 5 base I/O addressand IRQ. Serial Port 6 Configuration Use This Device Logical Device Settings When enabled allows you to configure the serial port 6 settings. Display the Serial Port 6 base I/O addressand IRQ. - 45 - BIOS Setup 2-3 Chipset Menu Onboard LAN1/2 Enable/Disable onboard LAN controller. This option provides user to set the mode of operation if an AC / power loss occurs. [. . . ]