User manual GIGABYTE GZ-X7

[. . . ] Features - All new Upgrade, Extremely Big Volume Extended Body, for easy installation and service, support SLI, Cross Fire Dual/ Quad multi-graphic cards, and support 12" x 13" motherboard. - High Quality Design Gigabyte Tech. top-class full tower thermal solution casing Lightweight aluminum alloy with hair-line brush anodized finishing Full-open aluminum side panel door design, with hair-line brush anodized finishing. 6 English - Complete Support Complete front panel multi-media support, including 4 x USB 2. 0, 1 x IEEE1394, 1 x audio jacks (HD & AC97) Full Support of Gigabyte Tech. thermal solution LCS and air-cooling products lines Support ATX / Micro ATX / Mini ATX / E-ATX / CEB motherboard. - Integration of Cooling Technology Aluminum alloy chassis for accelerating system cooling performance Gigabyte Liquid Cooling System situated in the top interior of the chassis. Automobile standard, aluminum radiator with dual 12cm silent fan on either side. [. . . ] Auto-induction of low water-level protection (LWP) and over temperature protection (OTP). 1. 0mm reinforced aluminum structure. - Convenience of Assembly Integrated LCS already installed, tested and ready to use. A single-handed latch to open the side panel, for easy disassembly. 7 English 3. Specification Features Model: GZ-FW1CA-AJS/AJB Case Type: FULL TOWER Size: 205 x 620 x 535 (W x H x D) Front Bezel Material: Aluminum Color: Silver/Black Side Panel: Vent mesh/Transparent acrylic Body Material: Aluminum (1. 0mm) / nickel-plated SECC (1. 0mm) Net weight: 12KG 5. 25" drive bay (external): 4 Controller 3. 5 drive bay (external): 2 3. 5 drive bay (internal): 5 PCI slot: 7 Motherboard size: ATX / Micro ATX / Mini ATX / E-ATX / CEB System Fan (Front): 1 x 12cm Silent Blue LED fan (1000 RPM) System Fan (Rear): 2 x 12cm Silent Blue LED fan (1000 RPM) LCS Fan (Top): 2 x 12cm adjustable fan (1000 RPM - 2600 RPM) Multi-Media I/O port: 4 x USB 2. 0 / 1 x IEEE1394 / 1 x audio jacks HD & AC97 8 English 4. Installation Instruction Please follow the reference sections in order for installation 4-1-3 Secure the power supply onto the retainer plate, by using the 4 fixed screws. To facilitate the installation, it is recommended to set the chassis upright on the table. Required Tools: power supply securing screw x 4 4-1-1 Remove the thumb screws of the left side panel and detach the left panel by unlatching the side panel. 4-1-2 Remove the thumb screws of the power supply retainer plate at the back of the chassis and remove. 4-1 Installation of Power Supply 4-1-4 Slide in the power supply from the rear of the chassis. 4-1-5 Use the thumb screws to secure the power supply retainer plate to the rear of the chassis. 9 English 4-1-6 If a longer power supply is used, please use the extended power supply retainer plate and secure with the extended screws. 4-1-7c Secure the power supply onto the retainer plate, by using the 4 fixed screws. 4-1-7d Remove the screws on the top cover of the chassis, two at the rear and two on either side of the chassis. 4-1-7 If an irregular size power supply is used which obstructs the product's sliding through the rear, please install the power according to the method mentioned below. 4-1-7a Remove the thumb screws of the side panels and detach both side panels. 4-1-7b Remove the thumb screws of the power retainer plate at the rear of the chassis, and remove the power retainer plate. 10 4-1-7e Remove the top cover after removing the lid to the coolant tank. English 4-1-7f Remove the screws on the liquid cooling system tray (above the power supply area and back panel, total of 5 screws. ) 4-1-7i Reverse the steps to reassemble the parts 4-2 Installation of Motherboard 3D Mercury can support ATX / Micro ATX / Mini ATX / E-ATX / CEB Please confirm the motherboard screw holes locations and size specification before installation Required Tools: Screwdriver, stand offs, and the motherboard screws 4-2-1 First remove the CPU water block from the motherboard tray on the chassis. 4-1-7g Gently lift the liquid cooling system tray and insert the power supply through the rear chassis. 4-1-7h If a longer power supply is used, please use the extended power supply retainer plate and secure with the extended screws. 11 English 4-2-2 If the motherboard is an LGA775, please use the back plate and stick it behind the motherboard. 4-2-5 Use the motherboard screws to secure the motherboard onto the back wall of the case (refer to your motherboard manual to check what type of motherboard you have). 4-2-3 According to the motherboard' s size specification, select the correct screw holes and insert the stand offs. Note: Incorrect installation may cause the motherboard to short circuit and other hardware to become faulty or damaged. Motherboard ATX Mini ATX Micro ATX E-ATX Motherboard screws 9 9 9 12 Code name A1-A9 M1-M9 U1-U9 E1-E12 Case copper post 9 9 9 12 4-3 Installation of Add on Card The 3D Mercury does not require any tools for installation of add-on cards such as graphics cards and network cards. d and e 4-13-7 To complete the liquid cooling system, after turning on the power, pour coolant into the tank till 80% full. 4-13-6 Before turning on the power, please make sure all tube clips are fastened tightly (such as Fig. a/b/c), and open the valves on the 4-way splitter valves (such as Fig. a, b and c Caution: While removing the tubes for disassembly, please make sure to close all valves on the 4-way splitter valve, 22 English turn off the power and keep all the devices away from any electronic part. Note: It is strongly recommended that all coolant is drained from the liquid cooling system prior to transportation of the computer system to prevent leakage if it is dropped or damaged. Although this has already been tested before the product is dispatched from the factory, the chassis is not designed to be transported with coolant inside the liquid cooling system. Warning: Use only GIGABYTE liquid coolant; any damage arising from the use of other liquid products is not covered by warranty. Leakage of liquid coolant due to improper installation may damage the system and is not covered by warranty. Place the chassis on a table or higher platform and put the empty container on the floor next to the chassis. Using the screwdriver, remove the bottom 4-way splitter valve from the chassis. e. Place the 4-way splitter valve outside of the chassis (Fig A), remove the right tube (Fig. It is now safe to transport the chassis or replace parts that need to be replaced. 4-14 Liquid Cooling System Maintenance c. [. . . ] Remove the 4 screws that secure the tank. 4-14-1 If If the coolant level is to low, remove the top lid and, after refilling coolant, secure the lid back on. 4-14-2 If pump makes strange noises, please make sure that there is no air inside the tubes. Please prepare a cross screwdriver and cloth (to clean the water leaks that may occur when disconnecting tubes). Please use the above-mentioned method to drain the coolant from the chassis. [. . . ]