User manual GIGABYTE GV-N610AX-1GI

[. . . ] Due to rapid change in technology, some of the specifications might be out of date before publication of this this manual. The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to update the information contained herein. Macrovision corporation product notice: This product incorporates copyright protection technology that is protected by U. S. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. [. . . ] Using non-official GIGABYTE BIOS might cause problem(s) on the graphics card. -7- Hardware Installation 2. 2. Hardware Installation Now that you have prepared your computer, you are ready to install your graphics card. If necessary, remove the metal cover from this slot; then align your graphics card with the PCI Express x16 slot, and press it in firmly until the card is fully seated. Make sure that the gold edge connector of the graphics card is securely inserted. Step 2. Replace the screw to fasten the card in place, and replace the computer cover. After installation, remember to connect the power cable to your graphics card, or the system will not boot (refer to page 8 to see the details). Do not touch the card when it's operating to prevent system instability. Step 3. Plug the display cable into your card; then turn on the computer and monitor. To connect a D-Sub monitor to your graphics card, use the D-Sub connector. To connect a flat panel display to your graphics card, use the DVI-I connector. To connect an HDMI monitor to your graphics card, use the HDMI connector. Connect an HDMI monitor To HDMI Monitor To D-Sub Monitor To Flat Panel Display Connect a D-Sub monitor Connect a flat panel display GV-N285 Series Graphics Accelerator -8- Step 4. To connect an HDMI TV, follow the steps below to enable the S/PDIF in function for the graphics card. 1. (the red wire connects to the S/PDIF out pin and the black to the Ground pin) You are now ready to proceed with the installation of the graphics card driver. To change video color settings, go to Adjust Video Color Settings under the Video and TV section from the Start page. Rotate Display The NVIDIA Rotate features enable you to change the orientation of your desktop to portrait, landscape, and inverted modes. This is useful if you have rotated your physical display and need to rotate the desktop to match the orientation of your display. Manage Custom Resolutions (Note) If you are an advanced user, you can create custom timing modes with the width, height, bit-color depth, and the refresh rate etc. The Advanced Timing page enables you to adjust timings for your graphics card in order to support a variety of different display timings for ultimate flexibility for analog CRT and DVI connections. You can use the advanced Change Resolution Attributes page to view custom display modes you have saved in the Create Custom Resolutions page. (Note) This item is present only in Advanced view mode. - 19 Software Installation Set Up Multiple Displays NVIDIA nView technology enables you to view your desktop in one of several multi-display modes to make the best use of the displays (monitors) that are connected to your computer. Dual-Monitor Setup You can set the display to output from two monitors on the Set Up Multiple Displays page. · Only use one display (Single) · The same on both display (Clone) · Configured independently from each other (Dualview) · As one large horizontal desktop (Horizontal span) (Note) · As one large vertical desktop (Vertical span) (Note) (1) The same on both display (Clone) Clone mode indicates that both displays in the display pair show images of the same desktop. Clone Mode (2) Configured independently from each other (Dualview) Dualview mode indicates that both displays in the display pair function as one virtual desktop. Unlike Horizontal Span or Vertical Span mode, Dualview treats each display as a separate device. This means that the taskbar will not be stretched across displays and 3D applications are not accelerated as efficiently as when the application spans displays. (Note) This item is present only in Windows XP. GV-N285 Series Graphics Accelerator Dualview Mode - 20 - (3) As one large horizontal desktop (Horizontal span) (Note 1) Horizontal Span mode indicates that both displays in the display pair function as one wide virtual desktop. The width of each display is half the width of the total virtual desktop width. Horizontal Span Mode (4) As one large vertical desktop (Vertical span) (Note 1) Vertical Span mode indicates that both displays in the display pair function as one tall virtual desktop. [. . . ] When the Windows Advanced Options Menu appears, select Safe Mode and press <Enter>. After getting into Safe Mode, in Device Manager check whether the driver for the graphics card is correct. For more assistance, use the Troubleshooting Guide located in the Windows Help or contact your computer manufacturer. If you are not able to find the desired monitor color/resolution settings: The color and screen resolution options available for selection depend on the graphics card being installed. [. . . ]