User manual GIGABYTE GS-R22PFL

[. . . ] For detailed product information, carefully read the Serice Guide. For product-related information, check on our website at: http://www. gigabyte. com Preface Before using this information and the product it supports, please read the following general information. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for GIGABYTE's "global" product offering. To better fit local marketrequirements and enhance product competitiveness, your regional office MAY have decided toextend the functionality of a machine (e. g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. [. . . ] · Disconnect the modem cable before opening a product enclosure, touching or installing internalcomponents, or touching an uninsulated modem cable or jack. · Do not use a telephone line to report a gas leak while you are in the vicinity of the leak. Federal Communications Commission (FCC) Statement Warning This is a class A product. In a domestic environment this product may cause radiointerfer-6- enceIn which case the user may be required to take adequate measures. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference when the equipment is operated in a commercial environment. This equipmentgenerates, uses, and can radiate radio frequency energy and, if not installed and used in accordance withthe instruction manual, may cause harmful interference to radio communications. Operation of thisequipment in a residential area is likely to cause harmful interference in which case the user will berequired to correct the interference at his own expense. Properly shielded and grounded cables and connectors must be used in order to meet FCC emissionlimits. Neither the provider nor the manufacturer are responsible for any radio or television interferencecaused by using other than recommended cables and connectors or by unauthorized changes ormodifications to this equipment. Unauthorized changes or modifications could void the user's authority tooperate the equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC part 68 (applicable to products fitted with USA modems) The modem complies with Part 68 of the FCC Rules. On this equipment is a label that contains, amongother information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company. If your telephone equipment causes harm to the telephone network, the Telephone Company maydiscontinue your service temporarily. But, if advance notice is notpractical, you will be notified as soon as possible. Push down the indentation located at the side of the back chassis and slide toward to remove the back chassis cover. - 13 - Hardware Installation 2-2 Installing the CPU Read the following guidelines before you begin to install the CPU: · Make sure that the motherboard supports the CPU. · Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage. Failure to properly turn off the server before you start installing componentsmay causeserious damage. Do not attempt the procedures described in the following sections unless youare a qualified servicetechnician. Follow these instructions to install the CPU: 1. Push down the indentation located at the side of the back chassis and slide toward to remove the back chassis cover. Hardware Installation - 14 - 2-3 1. 3. Installing the Heat Sink Apply thermal compound evenly on the top of the CPU. Place the heat sink(s) on top of the CPU and tighten the four positioning screws. Follow these instructions to install the heat sinks: - 15 - Hardware Installation 2-4 Installing the Memory Read the following guidelines before you begin to install the memory: · Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used. · Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage. If you are unable to insert the memory, switch the direction. 2-4-1 DualChannelMemoryConfiguration This motherboard provides four DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth. [. . . ] Orient the PCI card with the riser guide slot and push in the direction of the arrow until the PCI card sits in the PCI card connector. Align the riser bracket to the system module. Hardware Installation - 18 - 2-6 Installing the Hard Disk Drive Read the following guidelines before you begin to install the Hard disk drive: · Take note of the drive tray orientation before sliding it out. · The tray will not fit back into the bay if inserted incorrectly. · Make sure that the HDD is connected to the HDD connector on the backplane. Follow these instructions to Hard disk drive: 1. [. . . ]