User manual GIGABYTE GS-R22PDC

[. . . ] These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details. Please note WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reason, if a part number change is made, it will not be noted in the printed Service Guide. [. . . ] Close the plastic clip at both edges of the DIMM slots to lock the DIMM module. For dualquad channel operation, DIMMs must be installed in matched pairs. Reverse the installation steps when you wish to remove the DIMM module. 2 1 2 15 Hardware Installation Process 9 8 7 6 5 4 3 2 1 CPU2 12 11 10 CPU1 18 1716 15 14 13 No. 1 2 3 4 5 6 7 8 9 Code DDR_P1C2D0 DDR_P1C2D1 DDR_P1C2D2 DDR_P1C1D0 DDR_P1C1D1 DDR_P1C1D2 DDR_P1C0D0 DDR_P1C0D1 DDR_P1C0D2 16 No. 10 11 12 13 14 15 16 17 18 Code DDR_P0C0D2 DDR_P0C0D1 DDR_P0C0D0 DDR_P0C1D2 DDR_P0C1D1 DDR_P0C1D0 DDR_P0C2D2 DDR_P0C2D1 DDR_P0C2D0 Hardware Installation Process U-DIMM Population Table Channel A P0C0D0 P1C0D0 Single-Rank Dual-Rank P0C0D1 P1C0D1 x x P0C0D2 P1C0D2 x x x x x x P0C1D0 P1C1D0 Single-Rank Dual-Rank Channel B P0C1D1 P1C1D1 x x P0C1D2 P1C1D2 x x x x x x P0C2D0 P1C2D0 Single-Rank Dual-Rank Channel C P0C2D1 P1C2D1 x x P0C2D2 P1C2D2 x x x x x x U-DIMM Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Dual-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Dual-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Dual-Rank Dual-Rank 17 GS-R22PDC-RH Rack Mount Server R-DIMM Population Table Channel A P0C0D0 P1C0D0 Single-Rank Dual-Rank Quad-Rank P0C0D1 P1C0D1 x x x P0C0D2 P1C0D2 x x x x x x x x x x P0C1D0 P1C1D0 Single-Rank Dual-Rank Quad-Rank Channel B P0C1D1 P1C1D1 x x x P0C1D2 P1C1D2 x x x x x x x x x x P0C2D0 P1C2D0 Single-Rank Dual-Rank Quad-Rank Channel C P0C2D1 P1C2D1 x x x P0C2D2 P1C2D2 x x x x x x x x x x Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Dual-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Dual-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Dual-Rank Dual-Rank Quad-Rank Single-Rank Quad-Rank Single-Rank Quad-Rank Dual-Rank Quad-Rank Quad-Rank Quad-Rank Single-Rank Quad-Rank Dual-Rank Quad-Rank Quad-Rank R-DIMM Quad-Rank Dual-Rank Quad-Rank Quad-Rank Single-Rank Single-Rank Single-Rank Single-Rank Single-Rank Single-Rank Single-Rank Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Single-Rank Single-Rank Dual-Rank Dual-Rank Dual-Rank Single-Rank Dual-Rank Dual-Rank Single-Rank Dual-Rank Dual-Rank Single-Rank Dual-Rank Single-Rank Dual-Rank Single-Rank Dual-Rank Dual-Rank Dual-Rank Dual-Rank Single-Rank Dual-Rank Dual-Rank Single-Rank Dual-Rank Dual-Rank Dual-Rank Dual-Rank Single-Rank Dual-Rank Dual-Rank Dual-Rank Dual-Rank Dual-Rank Single-Rank Dual-Rank Dual-Rank Dual-Rank Dual-Rank 18 Hardware Installation Process Installing the PCI Expansion Card Step 1 Lift the riser bracket slightly, then pull it out from the server chassis. Step 3 Attach the mini card to the riser bracket and ecure the mini card with screws. Step 5 Slide the expansion card into the slot until the card firmly seats. Step 7 Align the riser bracket to the system module. 2 2 1 19 GS-R22PDC-RH Rack Mount Server 6 5 4 3 5 6 20 GS-R22PDC-RH Rack Mount Server Installing the Hard Disk Drive Step 1 Press the release button. Step 4 Secure the hard drive to the tray with four (4) screws as shown. Step 6 Connect cable and power. 1 3 2 4 4 21 Hardware Installation Process HDD Security Lock The HDD bays incorporate a security screw to prevent accidental HDD release. To engage the lock, turn the security screw clock-wise toward the Lock symbol. (Default setting) 2-3 close: Enable BIOS Recovery function. 2 ) CLR_CMOS1 (Clear CMOS jumper) You may clear the CMOS data to its default values by this jumper. Default value doesn't include the "Shunter" to prevent from improper use this jumper. To clear CMOS, temporarily short 2-3 pin. 1 1 1-2 close: Normal operation (Default setting) 2-3 close: Clear CMOS 40 GS-R22PDC-RH Rack Mount Server 3 ) CLR_RTC1 (Clear RTC jumper) 1 1 1-2 close: Normal operation. (Default setting) 2-3 close: Clear RTC status 4 ) ME_ENABLE (BMC Selection jumper) 1 1 1-2 Close: Normal operation. (Default setting) 2-3 Close: Enable BMC function. 5 ) PASS_DIS1 (Skip Supervisor password jumper) 1 1 1-2 Close: Normal operation. (Default setting) 2-3 Close: Clear Supervisor Password in BIOS setup menu. 6/7 ) JP_STRAP2/ JP_STRAP8 (PilotII firmware upgrade jumper) JP_STRAP2 1 1 1 JP_STRAP8 1 1 1 Descripeion Boot from BMC BOOT SPI Interface. Boot From internal ROM(Scratchpad Registers) Boot From internal ROM(Scratchpad Registers) 1 1 41 Jumper Setting Expansion Card Components Description The two riser cards installed in the PCI riser card bracket assembly povides support for both fullheoght and low-profile expansion cards. 1 2 Code PCI-E_X16_1 PCI-E_2 Description Full-height riser slot Low-profile riser slot 42 GS-R22PDC-RH Rack Mount Server BIOS Setup BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure required settings or to activate certain system features. The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard. When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS SRAM. ENTERINGSETUP When the power is turned on, press the <F2> button during the BIOS POST (Power-On Self Test) will take you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1". CONTROLKEYS <> <> <> <> <Esc> Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu <+/PgUp> Increase the numeric value or make changes <-/PgDn> <F1> <F2> <F3> <F4> <F6> <F7> <F8> <F9> <F10> Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Reserved Reserved Reserved Reserved Reserved Reserved Load the Optimized Defaults Save all the CMOS changes, only for Main Menu 43 BIOS Setup GETTINGHELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. [. . . ] Power On Stay Off Last State System power state when AC cord is re-plugged. (Default setting) 71 BIOS Setup Security About This Section: Security In this section, user can set either supervisor or user passwords, or both for different level of password securities. In addition, user also can set the virus protection for boot sector. Figure 4: Security Set Supervisor Password You can install and change this options for the setup menus. Type the password up to 6 characters in lengh and press <Enter>. [. . . ]