User manual GIGABYTE GS-R12P8G

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Chapter 1 Features Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Chapter 2 System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Chapter 3 System Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Step 2 Seat the heat sink in the retention modules with the four screws. Aling a DIMM on the socket such that the notch on the DIMM exactly match the notches in the socket. Firmly insert the DIMMinto the socket until the retaining clips snap back in place. When installing the DIMM into the DIMM socket, we recommend to populate one DIMM in Channel A module and one in Channel B module for best performance. Please note that each logical DIMM must be made of two identical DIMMs having the same device size on each and the same DIMM size. Reverse the installation steps when you wish to remove the DIMM module. Step 1 Step 2 Retaining Clip 14 Hardware Installation Process Step 3-5: PCI Expansion Card Installation GS-R12P8G provides expansion riser slots for one PCI-X full-height/full-length 64/66~100MHz; and one with PCI-E x8 slot. To install the peripheral, please go through the following steps. Note!!Before installing the PCI expansion card, please check the card size limitation. Size limitation for PCI-X full-height/full-length is 228. 5 mm x 91. 5 mm; size limitation for Low-Profile Card : 167. 5 mm x 56 mm . Step 1 Lift the riser bracket slightly, then pull it out from the server chassis. Step 3 Align the riser bracket to the system module (see the arrow direction mark 1), and push it to locked position. The delay ensures the hard disk initialized after powering up, prior to being accessed. Options Disabled, 3 Seconds, 6 Seconds, 9 Seconds, 12 Seconds, 21 Seconds, 30Seconds. Default vaule is Disabled. IDE Primary Master, Slave / Secondary Master, Slave, Parallel ATA The category identifies the types of hard disk from drive C to F that has been installed in the computer. Manual type is user-definable; Auto type which will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If you select User Type, related information will be asked to enter to the following items. Enter the information directly from the keyboard and press <Enter>. Such information should be provided in the documentation form your hard disk vendor or the system manufacturer. 29 GS-R12P8G Rack Mount Server TYPE 1-39: Predefined types. (Default Vaules) CD-ROM: Use for ATAPI CD-ROM drives or double click [Auto] to set all HDD parameters automatically. Multi-Sector Transfer This field displays the information of Multi-Sector Transfer Mode. Disabled: The data transfer from and to the device occurs one sector at a time. [. . . ] This will exit the Setup Utility and restart your compuetr when selecting this option. Press <Enter> on this item then system will reboot automatically. 55 GS-R12P8G Rack Mount Server Load Settup Default This option allows user to load default values for all setup items. When you press <Enter> on this item, you will get a confirmation dialog box with a message as below: Discard Changes This option allows user to load previos values from CMOS for all setup item. When you press <Enter> on this item, you will get a confirmation dialog box with a message as below: 56 BIOS Setup Save Changes This option allows user to save setup dat ato CMOS. [. . . ]