User manual GIGABYTE GS-R12P4S

[. . . ] 9 Contents Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 GS-R127-RH Series Model List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Chapter 1 Features Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Chapter 2 System Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To clear CMOS, temporarily short 2-3 pin. 1 1 1-2 close: Normal (Default setting) 2-3 close: Clear CMOS 28 BIOS Setup Chapter 5 BIOS Setup BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERINGSETUP Power ON the computer and press <F2> immediately will allow you to enter Setup. CONTROLKEYS <> <> < < > > Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu <+/PgUp> Increase the numeric value or make changes <-/PgDn> <F1> <F2> <F3> <F4> <F6> <F7> <F8> <F9> <F10> Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Reserved Reserved Reserved Reserved Reserved Reserved Load the Optimized Defaults Save all the CMOS changes, only for Main Menu <Esc> 29 GS-R127-RH Series Rack Mount Server GETTINGHELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window press <Esc>. Main This setup page includes all the items in standard compatible BIOS. Advanced This setup page includes all the items of AMI special enhanced features. (ex: Auto detect fan and temperature status, automatically configure hard disk parameters. ) Security Change, set, or disable password. It allows you to limit access the system and setup. Server Server additional features enabled/disabled setup menus. Boot This setup page include all the items of first boot function features. Exit There are five optionsin this selection: Exit Saving Changes, Exit Discarding Changes, Load Optimal Defaults, Load Failsafe Defaults, and Discard Changes. 30 BIOS Setup Main Once you enter Phoenix BIOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. Figure 1: Main System Time The time is calculated based on the 24-hour military time clock. Note that the "Day" automatically changed after you set the date. (Weekend: DD: MM: YY) (YY: 1099~2099) 31 GS-R127-RH Series Rack Mount Server IDE Primary Master, Slave / Secondary Master, Slave The category identifies the types of hard disk from drive C to F that has been installed in the computer. Manual type is user-definable; Auto type which will automatically detect HDD type. Note that the specifications of your drive must match with the drive table. (Default setting) Disable this function. C1 Enhanced Mode With enabling C1 Enhanced Mode, all loical processors in the physical processor have entered the C1 state, the processor will reduce the core clock frequency to system bus ratio and VID. (Default setting) Execute Disable Bit Enabled Disabled Enable Execute Disable Bit. (Default setting) 35 GS-R127-RH Series Rack Mount Server Advanced About This Section: Advanced With this section, allowing user to configure your system for basic operation. User can change the processor options, chipset configuration, PCI configuration and chipset control. Figure 2: Advanced 36 BIOS Setup Memory Configuration Figure 2-1: Memory Configuration System Memory/Extended Memory/DIMM Group 1~8 Status These category is display-only which is determined by POST (Power On Self Test) of the BIOS. Memory Reset Yes Select `Yes', system will clear the memory error status. After rebooting system, the Memory Reset item will set to `No' automatically. (Default setting) 37 GS-R127-RH Series Rack Mount Server Extend RAM Step Enabled Disabled Enable test extended memroy process. (Default setting) Memory Branch Mode Sequential Interleave Mirror Single Channel 0 Memory will use sequential mode to save date. Memory will use Interleave mode for to distribute every one memory to save date. Only Single channel 0 will be detect. Branch 0 Rank Sparing Enabled Disabled Enable this item, memory will spare two(dual channel) of all slots. (Default setting) Branch 1 Rank Sparing Enabled Disabled Enable this item, memory will spare two(dual channel) of all slots. (Default setting) 38 BIOS Setup PCI Configuration Figure 2-2: PCI Configuration Embedded NIC LAN 1 Option ROM Scan Enabled Disabled Enable onboard LAN1 device and initialize device expansion ROM. [. . . ] Click "Yes". 65 GS-R127-RH Series Rack Mount Server 4. Installation completed, Click "Finish" to restart computer. 66 Driver Installation B. ATI ES1000 VGA Driver Installation Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver CD-title will auto start and show a series of Setup Wizard dialog boxes. If not, please double click the CD-ROM device icon in "My computer", and execute the setup. exe. The CD auto run program starts, Double click on "ATI VGA Driver" to start the installation. [. . . ]