User manual GIGABYTE GA-H170TN

[. . . ] GA-H170TN User's Manual 12ME0-H17TN0-00R Motherboard GA-H170TN Motherboard GA-H170TN Jul. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. Documentation Classifications In order to assist in the use of this product, GIGABYTE provides the following types of documentations: „„ For detailed product information, carefully read the User's Manual. For product-related information, check on our website at: http://www. gigabyte. com Table of Contents Box Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GA-H170TN Motherboard Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Chapter 1 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1-1 1-2 1-3 1-4 1-5 1-6 Installation Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 1 2 Definition Mon_SW GND - 17 - 16) SATA_PWR (SATA Power Connector) This connector provides power to installed SATA devices. Connect the included SATA power cable to the SATA_PWR connector. Then connect the SATA/optical drive power connectors to your hard drive and optical drive. 17) SPKR (Speaker Header) This speaker header is connected to a L/R audio pins from the board to support the 3W (4ohm) stereo speaker on your AIO chassis. 4 1 Pin No. 1 2 3 4 Definition Speaker OUT RSpeaker OUT R+ Speaker OUT L+ Speaker OUT L- - 18 - 18) BATTERY (Battery Cable Connector) The battery provides power to keep the values (such as BIOS configurations, date, and time information) in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low level, or the CMOS values may not be accurate or may be lost. Pin No. 1 2 Definition RTC Reset GND 1 2 •• Always turn off your computer and unplug the power cord before replacing the battery. Danger of explosion if the battery is replaced with an incorrect model. •• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the battery model. •• Used batteries must be handled in accordance with local environmental regulations. 19) CLR_CMOS (Clearing CMOS Jumper) Use this jumper to clear the CMOS values (e. g. date information and BIOS configurations) and reset the CMOS values to factory defaults. To clear the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds. Open: Normal operation (Default setting) Close: Clear CMOS data •• Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values. •• After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or manually configure the BIOS settings (refer to Chapter 2, "BIOS Setup, " for BIOS configurations). - 19 - 20) LCD_VCC (LVDS Drive Boltage Jumper) This jumper can be used to provide different screen voltage settings. 1 1-2 Close: Set to 3V. 1 2-3 Close: Set to 5V. (Default setting) 21) FPD_PWR (Flat Panel Display Power Jumper) This jumper allows you to select the required operating voltage for the backlight panel. 1 1-2 Close: Set to 12V. 1 2-3 Close: Set to 19V. (Default setting) - 20 - 22) BL_SW (Back Light Switch) The Back Light switch provides the function for screen back light adjustment. 1 Pin No. 1 2 Definition BL_DOWN BL_UP 23) COM1 (Serial Port Header) The COM header can provide one serial port via an optional COM port cable. For purchasing the optional COM port cable, please contact the local dealer. Pin No. 1 2 3 4 5 6 7 8 9 10 Definition NDCDNDSRNSIN NRTSNSOUT NCTSNDTRNRIGND No Pin 10 9 2 1 - 21 - 24) M2_M (M. 2 Socket 3 Connector) You can insert an M. 2 SSD into this connector. F _ F _0 S S 25) M2_E (M. 2 Socket 1 Connector) You can insert an M. 2 Wifi card into this connector. _ S F_USB3 F S_ _ B _ U _ B _0 F F _ F _0 _ S U _ _ 3 F_USB3 F S B_ B S_ _ B _ U _ B - 22 S F B SS S B_ _0 F Chapter 2 BIOS Setup BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup, saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features. When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS. To access the BIOS Setup program, press the <Del> or <F12> key during the POST when the power is turned on. •• BIOS flashing is potentially risky, if you do not encounter problems of using the current BIOS version, it is recommended that you don't flash the BIOS. •• It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other unexpected results. [. . . ] The password length must be in the following range: Minimum length 3 Maximum length 20 Administrator Password User Password Secure Boot menu gf: Select Screen hi: Select Item ENTER: Select +/-: Change Opt. F1: General Help F3: Previous Values F9: Optimized Defaults F10: Save & Exit ESC: Exit There are two types of passwords that you can set: • Adminstrator Password Entering this password will allow the user to access and change all settings in the Setup Utility. • User Password Entering this password will restrict a user’s access to the Setup menus. To enable or disable this field, a Administrator Password must first be set. [. . . ]