User manual GIGABYTE GA-F2A75M-DS2

[. . . ] 3001 12ME-F275MS2-3001R Motherboard GA-F2A75M-DS2 Motherboard GA-F2A75M-DS2 Aug. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. [. . . ] - 19 - && DRAM Timing Selectable && Profile DDR Voltage Quick and Expert allows the memory timing settings below to be configurable. Options are: Auto (default), Quick, Expert. && Profile VTT Voltage When using a non-XMP memory module or Extreme Memory Profile (X. M. P. ) is set to Disabled, this item will display as 1. 50V. When Extreme Memory Profile (X. M. P. ) is set to Profile1 or Profile2, this item will display the value based on the SPD data on the XMP memory. The value displayed here is dependent on the CPU being used. && Rank Interleaving && Channel Interleaving Enables or disables memory rank interleaving. Enabled allows the system to simultaneously access different ranks of the memory to increase memory performance and stability. Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability. (Default: Enabled) `` Channel A/B Timing Settings This sub-menu provides memory timing settings for each channel of memory. The respective timing setting screens are configurable only when DRAM Timing Selectable is set to Quick or Expert. Note: Your system may become unstable or fail to boot after you make changes on the memory timings. If this occurs, please reset the board to default values by loading optimized defaults or clearing the CMOS values. `` Advanced Voltage Settings `` PC Health Status && Reset Case Open Status This sub-menu allows you to set CPU and memory voltages. && Case Open Disabled  Keeps or clears the record of previous chassis intrusion status. (Default) Enabled   Clears the record of previous chassis intrusion status and the Case Open field will show "No" at next boot. && CPU Vcore/Dram Voltage/+3. 3V/+5V/+12V Displays the detection status of the chassis intrusion detection device attached to the motherboard CI header. If the system chassis cover is removed, this field will show "Yes", otherwise it will show "No". To clear the chassis intrusion status record, set Reset Case Open Status to Enabled, save the settings to the CMOS, and then restart your system. Displays the current system voltages. && CPU/System Temperature && CPU/System Fan Speed && CPU Fan Speed Control Displays current CPU/system temperature. Displays current CPU/system fan speeds. && Slope PWM Allows you to determine whether to enable the fan speed control function and adjust the fan speed. Normal   Allows the fan to run at different speeds according to the CPU temperature. You can adjust the fan speed with EasyTune based on your system requirements. Manual  Allows you to control the fan speed under the Slope PWM item. This item is configurable only when CPU Fan Speed Control is set to Manual. - 20 - && System Fan Speed Control && Slope PWM Allows you to determine whether to enable the fan speed control function and adjust the fan speed. Normal Allows the fan to run at different speeds according to the system temperature. You can  adjust the fan speed with EasyTune based on your system requirements. [. . . ] Then browse to the USB flash drive that contains the driver and select the location of the driver. The locations of the drivers are as follows: RAID driver for Windows 8 32-bit: Hw8_A85\RAID\x86 RAID driver for Windows 8 64-bit: Hw8_A85\RAID\x64 AHCI driver for Windows 8 32-bit: Hw8_A85\AHCI\W8 AHCI driver for Windows 8 64-bit: Hw8_A85\AHCI\W864A For Windows 7, browse to the Hw7_A85 folder. After loading the driver, continue the OS installation. 3-2 Drivers Installation •• Before installing the drivers, first install the operating system. (The following instructions use Windows 8 as the example operating system. ) •• After installing the operating system, insert the motherboard driver disk into your optical drive. [. . . ]