User manual GIGABYTE GA-E350N

[. . . ] 1001 12ME-E350N-1001R Motherboard GA-E350N Motherboard GA-E350N Jun. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. [. . . ] This page is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results. (Inadequately altering the settings may result in system's failure to boot. If this occurs, clear the CMOS values and reset the board to default values. ) CMOS Setup Utility-Copyright (C) 1984-2012 Award Software IGX Configuration [Auto] [Auto] 492 Item Help Menu Level  UMA Frame Buffer Size VGA Core Clock control x VGA Core Clock(MHz) : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults && UMA Frame Buffer Size Frame buffer size is the total amount of system memory allocated solely for the onboard graphics controller. (Default: Auto) && VGA Core Clock control && VGA Core Clock(MHz) Allows you to set the onboard graphics clock. This item is configurable only if the VGA Core Clock control option is set to Manual. This item is present only when you install a CPU that supports this feature. - 23 - (Note) && CPU Frequency(MHz) Allows you to manually set the CPU host frequency. (Default: Normal) && CPU Host Clock Control Enables or disables the control of CPU host clock. Auto (default) allows the BIOS to automatically adjust the CPU host frequency. Note: If your system fails to boot after overclocking, please wait for 20 seconds to allow for automated system reboot, or clear the CMOS values to reset the board to default values. This item is configurable only when CPU Host Clock Control is set to Manual. (Default: Auto) This option is configurable only when Set Memory Clock is set to Manual. Options are: X5. 33, X6. 66. && CPU Host Clock && Set Memory Clock && Memory Clock && DRAM Configuration CMOS Setup Utility-Copyright (C) 1984-2012 Award Software DRAM Configuration [Auto] Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto [Enabled] SPD -- 9T 9T 9T 24T 5T 110ns -- 10T 5T 33T 4T -- Auto -8T 8T 8T 20T 4T 110ns -8T 4T 27T 4T -Item Help Menu Level  DDR3 Timing Items x 1T/2T Command Timing x CAS# latency x RAS to CAS R/W Delay x Row Precharge Time x Minimum RAS Active Time x TwTr Command Delay x Trfc0 for DIMM1 x Trfc1 for DIMM2 x Write Recovery Time x Precharge Time x Row Cycle Time x RAS to RAS Delay x Four Bank Activate Window Bank Interleaving : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults && DDR3 Timing Items Manual allows all DRAM timing control items below to be configurable. Options are: Auto (default), 5T~14T. && 1T/2T Command Timing && CAS# latency && RAS to CAS R/W Delay - 24 - && Row Precharge Time Options are: Auto (default), 5T~14T. Options are: Auto (default), 16T~40T. && Minimum RAS Active Time && TwTr Command Delay && Trfc0 for DIMM1 && Trfc1 for DIMM2 && Write Recovery Time && Precharge Time && Row Cycle Time && RAS to RAS Delay && Four Bank Activate Window && Rank Interleaving Enables or disables memory rank interleaving. Enabled allows the system to simultaneously access different ranks of the memory to increase memory performance and stability. (Default: Enabled) ******** System Voltage Optimized ******** && System Voltage Control Determines whether to manually set the system voltages. (Default) +0. 100V ~ +0. 300V The adjustable range is from +0. 100V to +0. 300V. Note: Increasing memory voltage may result in damage to the memory or reduce the useful life of the memory. Displays the normal operating voltage of your CPU. && DIMM Voltage && Normal CPU Vcore - 25 - 2-4 Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2012 Award Software Standard CMOS Features Date (mm:dd:yy) Tue, May 22 2012 Time (hh:mm:ss) 22:31:24 `` `` `` `` IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave Halt On Base Memory Extended Memory [None] [None] [None] [None] [All, But Keyboard] 640K 766M Item Help Menu Level  : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults && Date (mm:dd:yy) Sets the system date. Sets the system time. && Time (hh:mm:ss) && IDE Channel 0, 1 Master/Slave IDE HDD Auto-Detection Press <Enter> to autodetect the parameters of the SATA device on this channel. IDE Channel 0, 1 Master/Slave Configure your STA devices by using one of the two methods below: •• Auto Lets the BIOS automatically detect SATA devices during the POST. [. . . ] This exits the BIOS Setup without saving the changes made in BIOS Setup to the CMOS. Press <N> or <Esc> to return to the BIOS Setup Main Menu. Chapter 3 Drivers Installation •• Before installing the drivers, first install the operating system. •• After installing the operating system, insert the motherboard driver disk into your optical drive. The driver Autorun screen is automatically displayed which looks like that shown in the screen shot below. [. . . ]