User manual GIGABYTE GA-8IG1000-L

[. . . ] It can be switched between AGP 2X (3. 3V) or 4X(1. 5V) mode by adjusting the jumper. If you install this card in GA-8IG1000-L (or any AGP 4X only) motherboards without switching the jumper to 4X mode (1. 5V), it will burn the motherboard. Example 2: ATi Rage 128 Pro (Power Color) & SiS 305 golden finger is compatible with 2X/4X mode AGP slot, but it supports 2X(3. 3V) only. If you install this card in GA-8IG1000-L (or any AGP 4X only) motherboards, it will burn the motherboard. The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author make a commitment to up date the information contained herein. [. . . ] All Rights Reserved ACPI Sleep Type USB Dev Wakeup From S3 Suspend Time Out (Minute) Throttle Slow Clock Ratio Soft-Off by Power Button System After AC Back ModemRingOn/WakeOnLan PME Event Wake Up Resume by RTC Alarm RTC Alarm Date RTC Alarm Hour RTC Alarm Minute RTC Alarm Second KB & PS/2 Mouse Access FDC/LPT/COM Ports Access Pri. Slave IDE Access PIRQ[A] IRQ Active : S1/POS : Disabled : Disabled : 50. 0% : Instant Off : Off : Enabled : Enabled : Disabled : Every Day : 00 : 00 : 00 : Monitor : Monitor : Monitor : Ignore : Monitor : Ignore : Ignore ESC: Quit F1 : Help F5 : Old Values F6 : Fail-Safe F7 : Optimized F8: Flash Utility : Select Item PU/PD/+/- : Modify (Shift)F2: Color PIRQ[B] IRQ Active : Ignore PIRQ[C] IRQ Active : Ignore PIRQ[D] IRQ Active : Ignore Figure 5: Power Management Setup 37 GA-8IG1000-L Motherboard ACPI Sleep Type S1/POS S3/STR Set ACPI Sleep Type to S1/POS (Power On Suspend). (Default value) Set ACPI Sleep Type to S3/STR (Suspend To RAM). USB Dev Wakeup From S3 Enabled Disabled Enable USB Device Wakeup From S3. (Default value) Suspend Time Out Disabled 1Minute ~ 60 Minute Disable the timer to enter suspend mode. (Default Value) Set the timer to enter suspend mode. Throttle Slow Clock Ratio 12. 5%/25. 0%/37. 5%/50. 0% (Default Value)/62. 5%/75. 0%/87. 5% Soft-off by Power Button Instant off Suspend The user press the power button once, he can turn off the system. (Default Value) The user press the power button once, then he can enter suspend mode. System after AC Back Off On Last State When AC-power back to the system, the system will be in "Off" state. (Default Value) When AC-power back to the system, the system will be in "On" state. When AC-power back to the system, the system will return to the Last state before AC-power off. ModemRingOn/WakeOnLan Disabled Enabled Disable Modem Ring On / Wake On LAN function. The modem ring / LAN wake up will bring the system out of soft-off or suspend state if this option is set "Enabled". (Default Value) 38 BIOS Setup PME Event Wake up Disabled Enabled Disable PME event wake up function. The PME event wake up will bring the system out of soft-off or suspend state if this option is set "Enabled". (Y/N)?N DETECTION PNP / PCI CONFIGURATION IDE HDD AUTO LOAD FAIL-SAFE DEFAULTS LOAD OPTIMIZED DEFAULTS ESC: Quit F6: Fail-Safe Values SAVE & EXIT SETUP EXIT WITHOUT SAVING : Select Item F7: Optimized Values F8: Flash Utility F5: Old Values F10:Save & Exit Load Optimized Defaults Figure 8: Load Optimized Defaults Load Optimized Defaults Optimized defaults contain the most appropriate system parameter values to configure the system to achieve maximum performance. 44 BIOS Setup Integrated Peripherals AMIBIOS SETUP - INTEGRATED PERIPHERALS ( C ) 2001 American Megatrends, Inc. All Rights Reserved OnBoard IDE IDE1 Conductor Cable IDE2 Conductor Cable OnBoard FDC OnBoard Serial Port A OnBoard Serial Port B Serial Port B Mode IR Duplex Mode OnBoard CIR Port CIR IRQ Select OnBoard Parallel Port Parallel Port Mode EPP Version Parallel Port IRQ Parallel Port DMA OnBoard Midi Port Midi IRQ Select OnBoard Game Port Mouse PowerOn Function Keyboard PowerOn Function : Both : Auto : Auto : Auto : Auto : Auto : Normal : Half Duplex : Disabled : 10 : Auto : ECP : N/A : Auto : Auto : Disabled : 10 : 200 : Disabled : Disabled ESC: Quit F1 : Help F5 : Old Values F6 : Fail-Safe F7 : Optimized F8: Flash Utility : Select Item PU/PD/+/- : Modify (Shift)F2: Color Specific Key for PowerOn USB Function USB Legacy Support AC97 Audio AC97 Modem : N/A : Enabled : Disabled : Auto : Auto Figure 9: Integrated Peripherals 45 GA-8IG1000-L Motherboard OnBoard IDE Disabled Both Primary Secondary Disable OnBoard IDE. Only Secondary IDE channel is enabled. IDE1 Conductor Cable Auto ATA66/100 ATA33 Will be automatically detected by BIOS. (Default Value) Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). IDE2 Conductor Cable Auto ATA66/100 ATA33 Will be automatically detected by BIOS. (Default Value) Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). OnBoard FDC Disabled Enabled Auto Disable this function. (Default Value) Onboard Serial Port A Auto 3F8/COM1 2F8/COM2 3E8/COM3 2E8/COM4 Disabled BIOS will automatically setup the port A address. 46 BIOS Setup Onboard Serial Port B Auto 3F8/COM1 2F8/COM2 3E8/COM3 2E8/COM4 Disabled BIOS will automatically setup the port B address. Disable onboard Serial port B. Serial Port B Mode (This item allows you to determine which Infra Red(IR) function of Onboard I/O chip) ASKIR IrDa Normal Set onboard I/O chip UART to ASKIR Mode. (Default Value) IR Duplex Mode Half Duplex Full Duplex IR Function Duplex Half. [. . . ] Now the system will reboot automatically, the new BIOS setting will be taken effect next boot-up. AMIBIOS SIMPLE SETUP UTILITY - VERSION 1. 24b (C) 2001 American Megatrends, Inc. All Rights Reserved STANDARD CMOS SETUP BIOS FEATURES SETUP CHIPSET FEATURES SETUP POWER MANAGEMENT SETUP INTEGRATED PERIPHERALS HARDWARE MONITOR & MISC SETUP SUPERVISOR PASSWORD USER PASSWORD Save to CMOS and EXIT HDD AUTO DETECTION PNP / PCI CONFIGURATION IDE (Y/N)?Y LOAD BIOS DEFAULTS LOAD SETUP DEFAULTS ESC: Quit F6: Load BIOS Defaults : Select Item SAVE & EXIT SETUP EXIT WITHOUT SAVING (Shift)F2 : Change Color F5: Old Values F7: Load Setup Defaults F10:Save & Exit Save Data to CMOS & Exit SETUP 79 GA-8IG1000-L Motherboard STEP 5: BIOS flashing. (1) After the system boot from floppy disk, type "A:\> dir/w" and press "Enter" to check the entire files in floppy A. [. . . ]