User manual GIGABYTE GA-8IDX3

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X notch"(show below), please make sure your AGP card is AGP 4X (1. 5V). Do not use AGP 2X card (3. 3V) in this motherboard. It will burn and damage the motherboard due to Intel® 845 chipset can't support AGP 2X(3. 3V). Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. [. . . ] Note that there will not be any warning message if the drive installed is 360 K. Boot Up NumLock On Off Keypad is number keys. (Default value) Keypad is arrow keys. Password Check This category allows you to limit access to the system and Setup, or just to Setup. System Setup The system can not boot and can not access to Setup page will be denied if the correct password is not entered at the prompt. The system will boot, but access to Setup will be denied if the correct password is not entered at the prompt. (Default value) MPS Version Control For OS (Support Multi Processor Specification revision 1. 4) 1. 4 1. 1 Support MPS Version 1. 4 . (Default value) 29 GA-8IDX3 Series Motherboard Advanced Chipset Features CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Advanced Chipset Features Configure DRAM Timing CAS Latency Time Active to Precharge Delay DRAM RAS# to CAS# Delay DRAM RAS# Precharge Refresh Mode Select DRAM Data Integrity Mode DRAM Read Thermal Mgmt Delay Transaction AGP Aperture Size(MB) Delay Prior to Thermal SPD 3 6 3 3 15. 6usec Non-ECC Disable Enable 64 16Min Item Help Menu Level : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 4: Advanced Chipset Features Configure DRAM Timing SPD Manual Set Configure DRAM Timing Control by SPD. (Default value) Set SConfigure DRAM Timing Control by Manual. CAS latency Time 3 2 For Slower SDRAM DIMM module. (Default Value) For Fastest SDRAM DIMM module. Active to Precharge Delay 5 6 7 Set active to Precharge delay timing is 5 clk. Set active to Precharge delay timing is 6 clk. (Default value) Set active to Precharge delay timing is 7 clk. 30 BIOS Setup SDRAM RAS# to CAS# delay 3 2 Set SDRAM RAS# to CAS# delay 3 SCLKs. (Default value) Set SDRAM RAS# to CAS# delay 2 SCLKs. SDRAM RAS# Precharge 3 2 Set SDRAM RAS# Precharge Time to 3. (Default value) Set SDRAM RAS# Precharge Time to 2. Refresh Mode Select 7. 8 usec 15. 6 usec 64 usec Set active to Refresh mode timing is 7. 8 usec. Set active to Refresh mode timing is 15. 6 usec. (Default value) Set active to Refresh mode timing is 64 usec. DRAM Data Integrity Mode ECC Non-ECC Set DRAM Data Integrity Mode by ECC. (Default value) DRAM Read Thermal Mgmt Disabled Enabled Disable DRAM Read Thermal Mgme . (Default value) Enable DRAM Read Thermal Mgme. Delay Transaction Disabled Enabled Normal operation. (Default value) 31 GA-8IDX3 Series Motherboard AGP Graphics Aperture Size 4 8 16 32 64 128 256 AGP Graphics Aperture Size is 4MB. AGP Graphics Aperture Size is 16MB AGP Graphics Aperture Size is 32MB. AGP Graphics Aperture Size is 64MB. (Default Value) AGP Graphics Aperture Size is 128MB. AGP Graphics Aperture Size is 256MB. Delay Prior to Thermal 16Min 64Min Set active CPU Thermal function after booting 16 Min. (Default Value) Set active CPU Thermal function after booting 64 Min. 32 BIOS Setup Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2001 Award Software Integrated Peripherals On-Chip Primary PCI IDE On-Chip Secondary PCI IDE IDE Primary Master PIO IDE Primary Slave PIO IDE Secondary Master PIO IDE Secondary Slave PIO IDE Primary Master UDMA IDE Primary Slave UDMA IDE Secondary Master UDMA IDE Secondary Slave UDMA USB Controller USB Keyboard Support USB Mouse Support Init Display First AC97 Audio AC97 Modem Power On by Mouse Power On by Keyboard KB Power ON Password Onboard FDC Controller Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select UR2 Duplex Mode Onboard Parallel Port Parallel Port Mode ECP Mode Use DMA AC BACK Function Game Port Address Midi Port Address Enabled Enabled Auto Auto Auto Auto Auto Auto Auto Auto Enabled Disabled Disabled AGP Auto Auto Disabled Disabled Enter Enabled 3F8/IRQ4 2F8/IRQ3 Normal Half 378/IRQ7 SPP 3 Soft-Off 201 330 Menu Level Item Help 33 GA-8IDX3 Series Motherboard Midi Port IRQ CIR Port Address CIR Port IRQ 10 Disabled 11 : Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 5: Integrated Peripherals On-Chip Primary PCI IDE Enabled Disabled Enable onboard 1st channel IDE port. (Default value) Disable onboard 1st channel IDE port. On-Chip Secondary PCI IDE Enabled Disabled Enable onboard 2nd channel IDE port. (Default value) Disable onboard 2nd channel IDE port. IDE Primary Master PIO (for onboard IDE 1st channel) Auto BIOS will automatically detect the IDE HDD Accessing mode. (Default value) Mode0~4 Manually set the IDE Accessing mode. IDE Primary Slave PIO (for onboard IDE 1st channel) Auto BIOS will automatically detect the IDE HDD Accessing mode. (Default value) Mode0~4 Manually set the IDE Accessing mode. IDE Secondary Master PIO (for onboard IDE 2nd channel) Auto BIOS will automatically detect the IDE HDD Accessing mode. [. . . ] This is the first overdrive utility suitable for both normal and power users. Users can choose either "Easy Mode" or "Advanced Mode" to run "overdrive" at their convenience. For users who choose "Easy Mode", they just need to click "Auto Optimize" to have auto and immediate CPU overclocking. This software will then overdrive CPU speed automatically with the result being shown in the control panel. [. . . ]