User manual GIGABYTE GA-880GMA-USB3

[. . . ] GA-880GMA-USB3 AM3+ socket motherboard for AMD AM3+ processor AMD AM3 PhenomTM II processor/ AMD AthlonTM II processor User's Manual Rev. 3101 12ME-88GMAB3-3101R Motherboard GA-880GMA-USB3 Motherboard GA-880GMA-USB3 Mar. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. [. . . ] (Default: Enabled) If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to Disabled. Onboard USB 3. 0 Controller (Etron EJ168 USB Controller, USB Connectors on the Back Panel) USB Controllers Enables or disables the Etron EJ168 USB controller. (Default: Enabled) USB Legacy Function Enables or disables the integrated USB controllers. (Default: Enabled) Disabled will turn off all of the USB functionalities below. (Default: Enabled) USB Storage Function Onboard Serial Port 1 Determines whether to detect USB storage devices, including USB flash drives and USB hard drives during the POST. (Default: Enabled) Enables or disables the first serial port and specifies its base I/O address and corresponding interrupt. Options are: Auto, 2F8/IRQ3, 3F8/IRQ4(default), 3E8/IRQ4, 2E8/IRQ3, Disabled. BIOS Setup - 48 - 2-7 Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2011 Award Software Power Management Setup [S3(STR)] [Instant-off] [Enabled] [Disabled] [Enabled] [Enabled] [Disabled] [Disabled] Enter [Soft-Off] [Disabled] Everyday 0:0:0 [Disabled] Item Help Menu Level ACPISuspendType Soft-OffbyPowerbutton USBWakeUpfromS3 ModemRingResume PMEEventWakeUp HPET Support (Note) PowerOnByMouse PowerOnByKeyboard x KB Power ON Password ACBackFunction Power-OnbyAlarm x Date (of Month) x Resume Time (hh:mm:ss) ErPSupport Enter: Select higf: Move F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults ACPI Suspend Type Specifies the ACPI sleep state when the system enters suspend. S1(POS) Enables the system to enter the ACPI S1 (Power on Suspend) sleep state. In S1 sleep state, the system appears suspended and stays in a low power mode. S3(STR) Enables the system to enter the ACPI S3 (Suspend to RAM) sleep state (default). In S3 sleep state, the system appears to be off and consumes less power than in the S1 state. When signaled by a wake-up device or event, the system resumes to its working state exactly where it was left off. Configures the way to turn off the computer in MS-DOS mode using the power button. Instant-Off Press the power button and then the system will be turned off instantly. If the power button is pressed for less than 4 seconds, the system will enter suspend mode. Soft-Off by Power button USB Wake Up from S3 Modem Ring Resume Allows the system to be awakened from ACPI S3 sleep state by a wake-up signal from the installed USB device. (Default: Enabled) Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a modem that supports wake-up function. (Default: Disabled) Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a PCI or PCIe device. Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead. (Default: Enabled) PME Event Wake Up (Note) Supported on Windows 7/Vista operating system only. - 49 BIOS Setup HPET Support (Note) Enables or disables High Precision Event Timer (HPET) for Windows 7/Vista operating system. (Default: Enabled) Allows the system to be turned on by a PS/2 mouse wake-up event. Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead. (Default) Double Click Double click on left button on the PS/2 mouse to turn on the system. [. . . ] Is the power connector of the CPU cooler connected to the CPU_FAN header properly?Yes Yes Isolate the short circuit. The problem is verified and solved. Connect the CPU cooler power cable to the motherboard. The problem is verified and solved. No Correctly insert the memory into the memory socket. Check if the memory is installed properly on the memory slot. [. . . ]