User manual GIGABYTE GA-7N400

[. . . ] When you installing AGP card, please make sure the following notice is fully understood and practiced. If your AGP card has "AGP 4X/8X (1. 5V) notch"(show below), please make sure your AGP card is AGP 4X/8X. AGP 4X/8X notch Caution: AGP 2X card is not supported by nVIDIA® nForceTM 2 Ultra 400. Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X mode AGP slot. It can be switched between AGP 2X(3. 3V) or 4X(1. 5V) mode by adjusting the jumper. [. . . ] This function will available when "UART Mode Select" doesn't set at "Normal" nor "SCR". (Default Value) IR Function Duplex Full. Onboard Parallel port This feature allows you to select from a given set of parameters if the parallel port uses the onboard I/O controller. (Default Value) Enable onboard LPT port and address is 278, using IRQ5. Enable onboard LPT port and address is 3BC, using IRQ7. N400 Pro2 / N400 Series Motherboard - 52 - 7n400pro2_1001_b. p65 52 2003/7/4, ¤U¤È 03:29 Parallel Port Mode This feature allows you to connect with an advanced printer via the port mode it supports. (Default Value) Using Parallel port as ECP & EPP mode. English ECPMode UseDMA This feature allows you to select Direct Memory Access(DMA) channel if the ECP mode selected. This function will available when "Parallel Port Mode" set at ECP or ECP+EPP. (Default Value) Set ECP Mode Use DMA to 1. Game Port Address Disabled 201 209 Disable this function. (Default Value) Set Game Port Address to 209. Midi Port Address Disabled 330 300 Disable this function. (Default Value) Set Midi Port Address to 300. Midi Port IRQ 5 10 Set Midi Port IRQ to 5. (Default Value) - 53 - BIOS Setup 7n400pro2_1001_b. p65 53 2003/7/4, ¤U¤È 03:29 English Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software Power Management Setup ACPI Suspend Type Soft-Off by PWR-BTTN PME Event Wake Up ModemRingOn S3 Resume by USB Resume by Alarm x Date (of Month) Alarm x Time (hh:mm:ss) Alarm Power On by Mouse Power On by Keyboard x KB Power ON Password AC Back Function [S1(POS)] [Instant-off] [Enabled] [Enabled] [Disabled] [Disabled] Everyday 0:0:0 [Disabled] [Disabled] Enter [Soft-Off] [S3] Set suspend type to Suspend to RAM under ACPI OS Item Help Menu Level u [S1] Set suspend type to Power On Suspend under ACPI OS h i g f : Move Enter:Select +/-/PU/PD: Value F10: Save ESC:Exit F5: Previous Values F6: Fail-Safe Defaults Figure 6: Power Management Setup F1: General Help F7: Optimized Defaults ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend type to S1. (Default Value) Set ACPI suspend type to S3. Off by Power button Instant-off Delay 4 Sec. Enter suspend if button is pressed less than 4 sec. N400 Pro2 / N400 Series Motherboard - 54 - 7n400pro2_1001_b. p65 54 2003/7/4, ¤U¤È 03:29 PME Event Wake Up Disabled Enabled Disable this function. (Default Value) English ModemRingOn An incoming call via modem can awake the system from any suspend state . (Default Value) S3 Resume by USB You can resume the system from USB device. (Default Value) Enable this function. Resume by Alarm You can set "Resume by Alarm" item to enabled and key in Data/time to power on system. Date (of Month) Alarm : Everyday, 1~31 Time (hh: mm: ss) Alarm : (0~23) : (0~59) : (0~59) Power On By Mouse Disabled Mouse Click Disabled this function. (Default value) Double click on PS/2 mouse left button to power on the system. Power On By Keyboard - 55 - BIOS Setup 7n400pro2_1001_b. p65 55 2003/7/4, ¤U¤È 03:29 English This feature allows you to set the method for powering-on the system. The option "Password" allows you to set up to 5 alphanumeric characters to power-on the system. The option "Keyboard 98" allows you to use the standard keyboard 98 to power on the system. Password Disabled Keyboard 98 Enter from 1 to 5 characters to set the Keyboard Power On Password. (Default value) If your keyboard have "POWER Key" button, you can press the key to power on the system. KB Power ON Password When "Power On by Keyboard" set at Password, you can set the password here. Enter Input password (from 1 to 5 characters) and press Enter to set the Keyboard Power On password. AC BACK Function Soft-Off Full-On Memory When AC-power back to the system, the system will be in "Off" state. [. . . ] Question 12: For the M/B which have RAID function, how to set in the BIOS in order to bootup from IDE3, 4 by either RAID or ATA mode?Advanced BIOS features-->(SATA)/RAID/SCSI boot order: "SATA" 2. Integrated Peripherals--> Onboard H/W ATA/RAID: "enable" Then it depends on the RAID mode that you need to set "RAID" to RAID mode or "ATA" to normal ATA mode in the item named RAID controller function. Question 13: How to set in the BIOS to bootup from the IDE/ SCSI/ RAID card ? [. . . ]