User manual GIGABYTE GA-78LMT-S2PV

[. . . ] 5001 12ME-78LTS2V-5001R Motherboard GA-78LMT-S2PV Motherboard GA-78LMT-S2PV Oct. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. [. . . ] (Default: Auto) Allows you to manually set the width for the HT Link between the CPU and chipset. Allows you to manually set the frequency for the HT Link between the CPU and chipset. (Default) x1~x10  Sets HT Link Frequency to x1~x10 (200 MHz~2. 0 GHz). (Default: Auto) This option is configurable only when Set Memory Clock is set to Manual. Options are: X4. 00, X5. 33, X6. 66, X8. 00. && HT Link Frequency && Set Memory Clock && Memory Clock (Note) This item is present only when you install a CPU that supports this feature. - 19 - `` DRAM Configuration && DCTs Mode && DDR3 Timing Items Allows you to set memory control mode. (Default) Manual allows all DRAM timing control items below to be configurable. Options are: Auto (default), 4T~7T. && 1T/2T Command Timing && CAS# latency && RAS to CAS R/W Delay && Row Precharge Time && Minimum RAS Active Time && TwTr Command Delay && Trfc0 for DIMM1, DIMM3 && Trfc1 for DIMM2, DIMM4 && Write Recovery Time && Precharge Time && Row Cycle Time && RAS to RAS Delay && Channel Interleaving && Rank Interleaving Enables or disables memory channel interleaving. Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability. Enabled allows the system to simultaneously access different ranks of the memory to increase memory performance and stability. (Default: Enabled) Enables or disables memory DQS training each time the system restarts. (Default: Skip DQS) Determines whether to enable memory clock tri-stating in CPU C3 or Alt VID mode. (Default: Disabled) && DQS Training Control && Memclock tri-stating - 20 - ******** System Voltage Optimized ******** && System Voltage Control && NorthBridge Volt Control Determines whether to manually set the system voltages. (Default) +0. 1V ~ +0. 3V  The adjustable range is from 0. 1V to 0. 3V. (Default) 1. 500V ~ 1. 900V The adjustable range is from 1. 500V to 1. 900V.  Note: Increasing memory voltage may result in damage to the memory or reduce the useful life of the memory. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. Displays the normal operating voltage of your CPU North Bridge. && DDR3 Voltage && CPU Voltage Control && CPU NB VID Control && Normal CPU Vcore && Normal CPU Vcore NB 2-3 Standard CMOS Features Date (mm:dd:yy) Time (hh:mm:ss) ` ` ` ` IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave Halt On Base Memory Extended Memory Enter: Select : Move F5: Previous Values CMOS Setup Utility-Copyright (C) 1984-2012 Award Software Standard CMOS Features Mon, Sep 23 2013 22:31:24 [None] [None] [None] [None] [All, But Keyboard] 640K 766M +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults Item Help Menu Level  && Date (mm:dd:yy) && Time (hh:mm:ss) Sets the system date. Sets the system time. - 21 - && IDE Channel 0, 1 Master/Slave && Halt On IDE Channel 0, 1 Master/Slave  Options are: •• None  no IDE/SATA devices are used, set this item to None so the system will skip the If detection of the device during the POST for faster system startup. •• Auto Lets the BIOS automatically detect IDE/SATA devices during the POST. (Default) •• Manual  Allows you to manually enter the specifications of the hard drive when the hard drive access mode is set to CHS. [. . . ] To install Windows 64-Bit, copy the files in the x64 folder. Installing the SATA RAID/AHCI Driver and Operating System A. Installing Windows XP Restart your system to boot from the Windows XP setup disk and press <F6> as soon as you see the message "Press F6 if you need to install a 3rd party SCSI or RAID driver. " Insert the floppy disk containing the SATA RAID/AHCI driver. Follow the on-screen instructions to install the driver that suits your operating system. Installing Windows 7 Restart your system to boot from the Windows 7 setup disk and perform standard OS installation steps. [. . . ]