User manual GIGABYTE GA-78LMT-S2P

[. . . ] The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. [. . . ] Important It is highly recommended that the CPU frequency be set in accordance with the CPU specifications. (Default: Auto) Allows you to manually set the width for the HT Link between the CPU and chipset. Allows you to manually set the frequency for the HT Link between the CPU and chipset. HT Link Frequency Set Memory Clock Determines whether to manually set the memory clock. (Default: Auto) This item is present only when you install a CPU that supports this feature. DRAM Configuration x x x x x x x x x x x x CMOS Setup Utility-Copyright (C) 1984-2011 Award Software DRAM Configuration [Unganged] [Auto] Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto Auto [Enabled] [Enabled] [Skip DQS] [Disabled] +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults SPD -- 9T 9T 9T 24T 5T 90ns -- 10T 5T 33T 4T Auto -6T 6T 6T 15T 4T 90ns -6T 4T 20T 4T Item Help Menu Level  DCTs Mode DDR3 Timing Items 1T/2T Command Timing CAS# latency RAS to CAS R/W Delay Row Precharge Time Minimum RAS Active Time TwTr Command Delay Trfc0 for DIMM1 Trfc1 for DIMM2 Write Recovery Time Precharge Time Row Cycle Time RAS to RAS Delay Channel Interleaving Bank Interleaving DQS Training Control Memclock tri-stating Enter: Select : Move F5: Previous Values DCTs Mode DDR3 Timing Items Allows you to set memory control mode. - 24 - RAS to CAS R/W Delay Row Precharge Time Minimum RAS Active Time TwTr Command Delay Trfc0 for DIMM1 BIOS Setup Trfc1 for DIMM2 Write Recovery Time Precharge Time Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability. Enabled allows the system to simultaneously access different banks of the memory to increase memory performance and stability. (Default: Enabled) Enables or disables memory DQS training each time the system restarts. (Default: Skip DQS) Determines whether to enable memory clock tri-stating in CPU C3 or Alt VID mode. (Default: Disabled) DQS Training Control Memclock tri-stating ******** System Voltage Optimized ******** System Voltage Control DDR3 Voltage Control Determines whether to manually set the system voltages. NorthBridge Volt Control SouthBridge Volt Control CPU NB VID Control Allows you to set the CPU North Bridge VID voltage. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. - 25 BIOS Setup CPU Voltage Control Allows you to set the CPU voltage. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. IDE Channel 0, 1 Master/Slave IDE Channel 2 Master/Slave IDE Channel 0, 1 Master/Slave Configure your SATA devices by using one of the three methods below: •• None  no SATA devices are used, set this item to None so the system will skip the If detection of the device during the POST for faster system startup. €¢â€¢ Auto Lets the BIOS automatically detect SATA devices during the POST. (Default) •• Manual  Allows you to manually enter the specifications of the hard drive when the hard drive access mode is set to CHS. Extended IDE Drive Configure your SATA devices by using one of the two methods below: •• Auto Lets the BIOS automatically detect SATA devices during the POST. (Default) •• None  no SATA devices are used, set this item to None so the system will skip the If detection of the device during the POST for faster system startup. BIOS Setup - 26 - Halt On The following fields display your hard drive specifications. [. . . ] To create a new array, press <2> to enter the LD View/LD Define Menu window. To create an array, press <Ctrl+C> to access the LD Define Menu. In the LD Define Menu, use the up or down arrow key to move to an item for further configuration. Under the RAID Mode section, press the <SPACE> key to select RAID 0. [. . . ]