User manual GIGABYTE GA-78LMT-S2

[. . . ] The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.  In order to assist in the use of this product, carefully read the User's Manual. [. . . ] Enabled allows the system to simultaneously access different banks of the memory to increase memory performance and stability. (Default: Enabled) Enables or disables memory DQS training each time the system restarts. (Default: Skip DQS) Determines whether to enable memory clock tri-stating in CPU C3 or Alt VID mode. (Default: Disabled) DQS Training Control Memclock tri-stating ******** System Voltage Optimized ******** System Voltage Control DDR3 Voltage Determines whether to manually set the system voltages. (Default) 1. 500V ~ 1. 900V The adjustable range is from 1. 500V to 1. 900V. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. - 24 - CPU Voltage Control CPU NB VID Control Normal CPU Vcore Normal CPU Vcore NB Displays the normal operating voltage of your CPU. Displays the normal operating voltage of your CPU North Bridge. 2-4 Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2012 Award Software Standard CMOS Features Date (mm:dd:yy) Thu, Apr 19 2012 Time (hh:mm:ss) 22:31:24 } } } } } } IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 1 Master IDE Channel 1 Slave IDE Channel 2 Master IDE Channel 2 Slave Halt On Base Memory Extended Memory [None] [None] [None] [None] [None] [None] [All, But Keyboard] 640K 766M ESC: Exit F1: General Help F7: Optimized Defaults Item Help Menu Level  : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults Date (mm:dd:yy) Time (hh:mm:ss) Sets the system date. Sets the system time. IDE Channel 0, 1 Master/Slave IDE Channel 0, 1 Master/Slave Configure your SATA devices by using one of the three methods below: •• None  If no SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup. •• Auto Lets the BIOS automatically detect SATA devices during the POST. Capacity Approximate capacity of the currently installed hard drive. Extended IDE Drive Configure your SATA devices by using one of the two methods below: •• Auto Lets the BIOS automatically detect SATA devices during the POST. (Default) •• None  If no SATA devices are used, set this item to None so the system will skip the detection of the device during the POST for faster system startup. Capacity Approximate capacity of the currently installed hard drive. Allows you to determine whether the system will stop for an error during the POST. Options are: "All Errors, " "No Errors, " "All, But Keyboard". (Default) These fields are read-only and are determined by the BIOS POST. - 25 - IDE Channel 2 Master/Slave Halt On Memory 2-5 Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2012 Award Software Advanced BIOS Features } IGX Configuration [Press Enter] Load Line Control [Auto] AMD C1E Support [Disabled] Virtualization [Disabled] AMD K8 Cool&Quiet control [Auto] CPU Unlock (Note) [Disabled] CPU core Control (Note) [Auto] x CPU core 0 (Note) Enabled x CPU core 1 (Note) Enabled x CPU core 2 (Note) Enabled x CPU core 3 (Note) Enabled } Hard Disk Boot Priority [Press Enter] EFI CD/DVD Boot Option [Auto] First Boot Device [Hard Disk] Second Boot Device [CDROM] Third Boot Device [USB-HDD] Password Check [Setup] HDD S. M. A. R. T. Capability [Disabled] Away Mode [Disabled] Full Screen LOGO Show [Enabled] Init Display First [PCI Slot] Item Help Menu Level  : Move Enter: Select F5: Previous Values +/-/PU/PD: Value F10: Save F6: Fail-Safe Defaults ESC: Exit F1: General Help F7: Optimized Defaults IGX Configuration Load Line Control The settings in this submenu are synchronous to those under the same items on the MB Intelligent Tweaker(M. I. T. ) main menu. Enabling Load Line control may keep the CPU voltage more constant under light and heavy CPU load. (Default: Auto) Enables or disables the C1E CPU power-saving function in system halt state. [. . . ] 8. Press <Esc> to return to Main Menu and press <Esc> again if you want to exit the RAID BIOS utility. - 37 - Making a SATA RAID/AHCI Driver Diskette Before installing Windows XP, connect a USB floppy disk drive to your computer first because you need to install the SATA RAID/AHCI driver from a floppy disk that contains the driver during the OS installation. To copy the RAID/AHCI driver for Windows XP, copy all files in the \BootDrv\SBxxx folder in the motherboard driver disk to your floppy disk. Installing the SATA RAID/AHCI Driver and Operating System A. Installing Windows XP Restart your system to boot from the Windows XP setup disk and press <F6> as soon as you see the message "Press F6 if you need to install a 3rd party SCSI or RAID driver. " Insert the floppy disk containing the SATA RAID/AHCI driver. Follow the on-screen instructions to install the driver that suits your operating system. [. . . ]