User manual GIGABYTE GA-6FASV1

[. . . ] GA-6FASV Series Xeon Processor Motherboard USER'S Manual Xeon® Processor Motherboard Rev. 1001 * The WEEE marking on the product indicates this product must not be disposed of with user's other household waste and must be handed over to a designated collection point for the recycling of waste electrical and electronic equipment!!The WEEE marking applies only in European Union's member states. * GA-6FASV Series Motherboard Table of Contents Item Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Chapter 1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Dispose of used batteries according to the manufacturer's instructions. 21 GA-6FASV Series Motherboard 14/15/16/17 ) FAN1/2/3/4 (CPU fan/System fan cable connectors) The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin(CPU_FAN) power connector and possesses a foolproof connection design. A red power connector wire indicates a positive connection and requires a +12V power voltage. Remember to connect the CPU/system fan cable to the CPU_FAN/SYS_FAN connector to prevent CPU damage or system hanging caused by overheating. 1 FAN2 1 Pin No. 1 2 3 4 Definition GND 12V Sense Control FAN1 FAN3 FAN4 18 )AUDIO (Front AUDIO connector/Option) In order to utilize the front audio header, your chassis must have front audio connector. Also please make sure the pin assignment on the cable is the same as the pin assignment on the MB header. To find out if the chassis you are buying support front audio connector, please contact your dealer. 1 2 3 4 5 6 7 8 9 10 11 12 12 11 Definition Line IN (R) MIC (R) Line IN (L) MIC (L) Line IN Jack Detect GND GND Line Out Jack Detect Line Out (R) MIC Jack Detect Line Out (L) Key 22 GA-6FASV Series Motherboard Jumper Setting 23 24 22 21 20 19 23 GA-6FASV Series Motherboard 19 ) CLR_CMOS1 (Clear CMOS jumper) You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily short 2-3 pin. 1 1-2 close: Normal operation (Default setting) 1 2-3 close: Clear CMOS 20 ) PASSWORD1 (Set Supervisor password jumper) 1 1 1-2 Close: Set Supervisor Password. (Default setting) 2-3 Close: Clear Supervisor Password in BIOS setup menu. 21 ) BIOS_RVCR1 (BIOS Recovery jumper) 1 1-2 close: Normal operation. (Default setting) 1 2-3 close: Enable BIOS Recovery function. 22 ) USB_PWR1 (USB1 power source selection jumper) 1 1 1-2 close: Normal power operation. (Default setting) 23 ) USB_PWR2 (USB2 power source selection jumper) 1 1 1-2 close: Normal power operation. (Default setting) 24 ) USB_PWR3 (USB3 power source selection jumper) 1 1-2 close: Normal power operation. (Default setting) 24 GA-6FASV Series Motherboard Chapter 3 BIOS Setup BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure required settings or to activate certain system features. The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard. When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS SRAM. ENTERINGSETUP When the power is turned on, press the <F2> button during the BIOS POST (Power-On Self Test) will take you to the CMOS SETUP screen. You can enter the BIOS setup screen by pressing "Ctrl + F1". CONTROLKEYS <> <> <> <> <Esc> Move to previous item Move to next item Move to the item in the left hand Move to the item in the right hand Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu - Exit current page and return to Main Menu <+/PgUp> Increase the numeric value or make changes <-/PgDn> <F1> <F2> <F3> <F4> <F6> <F7> <F8> <F9> <F10> Decrease the numeric value or make changes General help, only for Status Page Setup Menu and Option Page Setup Menu Reserved Reserved Reserved Reserved Reserved Reserved Load the Optimized Defaults Save all the CMOS changes, only for Main Menu 25 GA-6FASV Series Motherboard GETTINGHELP Main Menu The on-line description of the highlighted setup function is displayed at the bottom of the screen. Status Page Setup Menu / Option Page Setup Menu Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. Select the Load Setup Defaults item in the BIOS Exit Setup menu when somehow the system is not stable as usual. This action makes the system reset to the default settings for stability. Main This setup page includes all the items in standard compatible BIOS. Advanced This setup page includes all the items of Phoenix BIOS special enhanced features. (ex: Auto detect fan and temperature status, automatically configure hard disk parameters. ) Power This setup page includes all the items of Green function features. Security Change, set, or disable password. It allows you to limit access the system and setup. Server Server additional features enabled/disabled setup menus. Boot This setup page include all the items of first boot function features. Exit There are five options in this selection: Exit Saving Changes, Exit Discarding Changes, Load Optimal Defaults, Load Failsafe Defaults, and Discard Changes. 26 GA-6FASV Series Motherboard Main Once you enter Phoenix BIOS Setup Utility, the Main Menu (Figure 1) will appear on the screen. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu. Figure 1: Main System Date Set the System Date. Note that the "Day" automatically changed after you set the date. System Time The time is calculated based on the 24-hour military time clock. [. . . ] You may also press <Esc> to abort the selection and not enter a specified password or press <Enter> key to disable this option. 51 GA-6FASV Series Motherboard Set User Password You can only enter but do not have the right to change the options of the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Type the password up to 6 characters in length and press <Enter>. The password typed now will clear any previously entered password from the CMOS memory. [. . . ]