User manual GIGABYTE G1.SNIPER 2

[. . . ] 1001 12ME-Z68SNI2-1001R Motherboard G1. Sniper 2 Motherboard G1. Sniper 2 Jul. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. Documentation Classifications In order to assist in the use of this product, GIGABYTE provides the following types of documentations: For quick set-up of the product, read the Quick Installation Guide included with the product. [. . . ] Current CPU FAN Speed Current FAN1 Speed Current FAN2 Speed Current FAN3 Speed Current FAN4 Speed CPU Warning Temperature [Disabled] No 1. 172V 1. 536V 11. 779V 3. 205V 5. 042V 1. 076V 47oC 33oC 40oC 46oC 40oC 3375 RPM 0 RPM 0 RPM 0 RPM 0 RPM [Disabled] +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save Item Help Menu Level Enter: Select higf: Move F5: Previous Values ESC: Exit F1: General Help F7: Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2011 Award Software PC Health Status CPU FAN Fail Warning FAN1 Fail Warning FAN3 Fail Warning CPU Smart FAN Control x Slope PWM [Disabled] [Disabled] [Disabled] [Normal] 1. 75 PWM value /oC Item Help Menu Level Enter: Select higf: Move F5: Previous Values +/-/PU/PD: Value F6: Fail-Safe Defaults F10: Save ESC: Exit F1: General Help F7: Optimized Defaults Reset Case Open Status Keeps or clears the record of previous chassis intrusion status. Enabled clears the record of previous chassis intrusion status and the Case Openedfieldwillshow"No"atnextboot. (Default:Disabled) Case Opened Displays the detection status of the chassis intrusion detection device attached to the motherboard CI header. Ifthesystemchassiscoverisremoved, thisfieldwillshow"Yes", otherwiseitwillshow"No". To clear the chassis intrusion status record, set Reset Case Open Status to Enabled, save the settings to the CMOS, and then restart your system. Current Voltage(V) Vcore/DDR15V/+12V/Vcc3/Vcc/Vtt Displays the current system voltages. BIOS Setup - 56 - Current CPU Temperature Current System1 Temp. /System2 Temp. /System3 Temp. /System4 Temp. Current CPU FAN/FAN1/FAN2/FAN3/FAN4 Speed (RPM) CPU Warning Temperature Displays current CPU/system/power fan speed. Displays current system temperatures detected by each system temperature sensor on the motherboard. Displays current CPU temperature. CPU FAN/FAN1/FAN3 Fail Warning Sets the warning threshold for CPU temperature. When CPU temperature exceeds the threshold, BIOS will emit warning sound. Options are: Disabled (default), 60oC/140oF, 70oC/158oF, 80oC/176oF, 90oC/194oF. Allows the system to emit warning sound if the CPU/system fan is not connected or fails. (Default: Disabled) Allows you to determine whether to enable the CPU fan speed control function and adjust the fan speed. Normal Allows the CPU fan to run at different speeds according to the CPU temperature. You can adjust the fan speed with EasyTune based on your system requirements. Manual Allows you to control the CPU fan speed under the Slope PWM item. Disabled Allows the CPU fan to run at full speeds. CPU Smart FAN Control Slope PWM AllowsyoutocontroltheCPUfanspeed. ThisitemisconfigurableonlywhenCPU Smart FAN Control is set to Manual. Options are: 0. 75 PWM value /oC ~ 2. 50 PWM value /oC. - 57 - BIOS Setup 2-9 Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2011 Award Software MB Intelligent Tweaker(M. I. T. ) Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PC Health Status Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Load Fail-Safe Defaults Save & Exit Setup (Y/N)?N Exit Without Saving higf: Select Item F10: Save & Exit Setup Load Fail-Safe Defaults F11: Save CMOS to BIOS F12: Load CMOS from BIOS ESC: Quit F8: Q-Flash Press <Enter> on this item and then press the <Y> key to load the safest BIOS default settings. In case system instability occurs, you may try to load Fail-Safe defaults, which are the safest and most stable BIOS settings for the motherboard. 2-10 Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2011 Award Software MB Intelligent Tweaker(M. I. T. ) Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PC Health Status Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & N Load Optimized Defaults (Y/N)?Exit Setup Exit Without Saving higf: Select Item F10: Save & Exit Setup Load Optimized Defaults F11: Save CMOS to BIOS F12: Load CMOS from BIOS ESC: Quit F8: Q-Flash Press <Enter> on this item and then press the <Y> key to load the optimal BIOS default settings. The BIOS defaults settings help the system to operate in optimum state. Always load the Optimized defaults after updating the BIOS or after clearing the CMOS values. BIOS Setup - 58 - 2-11 Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2011 Award Software MB Intelligent Tweaker(M. I. T. ) Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management SetupEnter Password: PC Health Status higf: Select Item F10: Save & Exit Setup Change/Set/Disable Password Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving F11: Save CMOS to BIOS F12: Load CMOS from BIOS ESC: Quit F8: Q-Flash Press <Enter> on this item and type the password with up to 8 characters and then press <Enter>. You will berequestedtoconfirmthepassword. Typethepasswordagainandpress<Enter>. The BIOS Setup program allows you to specify two separate passwords: Supervisor Password When a system password is set and the Password Check item in Advanced BIOS Features is set to Setup, you must enter the supervisor password for entering BIOS Setup and making BIOS changes. When the Password Check item is set to System, you must enter the supervisor password (or user password) at system startup and when entering BIOS Setup. User Password When the Password Check item is set to System, you must enter the supervisor password (or user password) at system startup to continue system boot. [. . . ] Is the power connector of the CPU cooler connected to the CPU_FAN header properly?Yes Yes Isolate the short circuit. Theproblemisverifiedandsolved. Connect the CPU cooler power cable to the motherboard. Theproblemisverifiedandsolved. No Correctly insert the memory into the memory socket. Check if the memory is installed properly on the memory slot. [. . . ]