User manual GEONAUTE WATCH OUTDOOR 500WW

[. . . ] uu M O ont ut r do e o or ut 50 wa doo 0W tch r W 9 8 10 6 2 LIMITED WARRANTY GEONAUTE guarantees the initial purchaser that this watch is free from defects of materials or manufacture for a period of two years from the date of purchase. - This guarantee does not cover damage resulting from misuse, from a failure to respect the precautions for use nor from accidents; neither does this guarantee cover damage resulting from improper maintenance or from use of the item for commercial purposes. - This warranty does not cover damage resulting from repairs carried out by persons not authorized by GEONAUTE. [. . . ] Deposit the batteries and your unusable electronic product in an authorized collection area for recycling. This treatment of your electronic waste will protect the environment and your health. 1 - Time mode (TIME) S1 : alternate between temperature/UV index displays S2 : change the time zone S3 : switch to the next mode. S4 : quick press: electroluminescence long press: enter setting mode S4 MI UV LO UV INDEX 14. 0 T1 S1 P 12:3845 WE 1-01 S3 S2 NAVIGATION SYSTEM This watch has 7 operating modes: A time mode An alarm mode A stopwatch mode A countdown mode A tide schedule mode A temperature mode A UV index measurement mode The procedure for going from one mode to another is shown in the following diagram: S3 Time/date Alarm S3 Stopwatch S3 Countdown feature Recall S3 S3 S3 Tide S3 Temperature S3 UV In normal mode, the watch displays the time and the date, including the day of the week, as well as the temperature, the UV index and the tides. SETTING THE TIME · Press on S4 for 2 seconds: enter time setting mode and the "NIGHT OFF" symbol will flash. · Press on S1: activate the "NIGHT ON" option (electroluminescence when you press on each function): the "moon and star" symbol is displayed (press on S2 to deactivate this option). Proceed in this manner to successively set the minutes, the seconds, the year, the month and the day of the month. S4 24 25 EN · Press on S4 at any time to exit time setting mode. The day of the week is calculated automatically within a period from 2003 to 2053. 2 - Alarm mode (ALARM) S1 : activate/deactivate the alarm S2 : activate/deactivate the hourly beep S4 S3 : switch to the next mode. S4 : quick press: S3 electroluminescence long press: set the alarm UV INDEX MI UV LO DISPLAY OF MOON MODES On the watch, an icon indicates the current moon phase. The phases are indicated according to the table below: 14. 0 T1 S1 P 12:00AL WE 1-01 S2 3 2 USING THE ALARM 4 · Press on S1: activate and deactivate the selected alarm. · Press on S2: activate and deactivate the hourly beep (chimes). 5 1 SETTING THE ALARM 8 7 6 26 1 - New moon 2 - Waxing crescent 3 - First quarter 4 - Waxing gibbous 5 - Full moon 6 - Waning gibbous 7 - Last quarter 8 - Waning crescent and the cycle starts over until the next new moon · Press on S4 for 2 seconds: enter setting mode and the hour digits will flash. · Press on S4 at any time to exit setting mode. 27 EN 3 - Stopwatch mode (CHRONO) S1 : start/stop stopwatch S4 S2 : lap time/clear the stopwatch 00'00"00 (long press) S3 S3 : switch to next mode S4 : quick press: electroluminescence long press: enter lap time recall mode UV INDEX MI UV LO The LAP is the time elapsed since the last lap time. 0 S1 14. 0 P STW CHRON S2 Split1 Lap1 Split 2 Lap 2 Split 3 Lap 3 Split 4 Lap 4 USING THE STOPWATCH · Press on S1: start the stopwatch and the STW symbol is displayed while the stopwatch is timing. · Press for 2 seconds on S2: "RESET" is displayed and the stopwatch is cleared. · Press on S1: start the stopwatch. The screen displays the LAP and the SPLIT for 3 seconds then goes back to the display of the current time. · Press on S2 for 2 seconds: "RESET" is displayed and the stopwatch is cleared. The stopwatch can measure times up to 23 hours, 59 minutes and 59 seconds. LAP TIMES The stopwatch included with this watch features 30 lap times. [. . . ] · Press on S1 or S2: set the high tide parameter and the low tide parameter for the next tide. · Press on S4 at any time to exit setting mode. 6 - Temperature mode S1: alternatively displays the temperature in ° Celsius or in °Fahrenheit S2: inactive S3: switch to the next mode. S4: quick press: electroluminescence long press: enter calibration mode S4 MI UV LO UV INDEX 1 - Low tide 14. 0 S1 P S3 TEMP 14. 0C S2 TMR 2 - Rising tide A graphic display shows the current status of the tide in 4 phases: 3 - High tide 4 - Falling tide 32 And the cycle starts over. . . USING THE TEMPERATURE FUNCTION The temperature is measured within a range from ­9. 9°C to +69. 9°C (14°F to +158°F). [. . . ]