User manual GEONAUTE WATCH KRONYS 200D

[. . . ] as "water · Waterproof design: The stopwatch is classifiedrain or waterresistant". Itit can therefore be used in humid conditions and is water-resistant in spray. But is not waterproof in cases of immersion, nor is it designed to be used under water. maintenance To preserve the Decathlon repair must be · Care andentrusted to a :Decathlon electronics shop. guarantee, any operation ordysfunction can exclusively If one is not available, no be claimed in the context of the Decathlon guarantee, with the exception of hidden defects. [. . . ] Remember to protect the environment and dispose of your batteries or your used product in a place where they can be recycled. The settings for time, date, TIMER, and PACER are explained in the sections dedicated to the different modes. AM:12':30'4' 3 SU 12:07'0' 0 2004'0' 0 FULL SPEED TIME START/STOP : lactivate/deactivate the beeping sound RECALL : to enter the setting mode SPLIT/RESET : to go to 12/24h mode MODE : go to the following mode 19 18 Display ·Top line ::Time - Middle line : Day, week and date - Bottom line : Year TIME the lower left · The screen will display the wordappear at the function is of the screen. corresponding The symbol for the daily alarm will if selected (see chapter). The sound that signals activation of the buttons is also present in the lower left of the screen if activated (press START/STOP to activate or deactivate). 2 Daily Alarm Mode AM:07':06''39 ALARM'0' 0 PM:02':00''00 START/STOP : activate/deactivate the alarm RECALL : to enter the setting mode SPLIT/RESET : inactive MODE : go to the following mode Display ·Top line ::Time - Middle line : Alarm - Bottom line : Wake-up time · A brief display on the middle line (Time) indicates that you have entered this mode. · START/STOP : loud beep when entering the setting mode · On the top line, you will read the time in Anglo-Saxon mode (0-12 hours AM/PM) or in European mode (0-24 hours). Going from one to the other is done by pressing the SPLIT/RESET button. On the middle line, you will read the date in the format day week-day of the month-month or week-month-day of the month respectively, depending on whether the European mode (EU) or Anglo-Saxon mode (US) has been activated (see settings chapter) The current year will appear on the lower line. The day of the week is automatically calculated based on the year and the date. The word SET and the number of seconds will flash to indicate that you have entered the setting mode. · · Press the SPLIT/RESET button repeatedly to change theinparameter to set, following sequence . . . seconds-hour-minutes-year-month-day-display European or Anglo-Saxon mode (date in the format DD/MM or MM//YY). . . When the elements flash, press the START/STOP button to reset the seconds to 0 or scroll through the numbers of the parameter to the desired value. Press RECALL again to leave the setting mode. · The symbol for the daily alarm will appear if the function is selected (see corresponding chapter). The word ALARM will appear for several seconds once you have arrived in this mode, and then remain displayed on the middle line. will read · On the top line, you12h or 24hthe time displayed according to the setting made in the preceding chapter, in mode. On the bottom line, you will read the alarm time in the same format as that of the time, set in the time date mode. Press the START/STOP button to alternate between activating and deactivating the alarm. Press the SPLIT/RESET button repeatedly to change the parameter to be set following the sequence . . . number of the timer-hour-minutes-seconds. . . When one of the elements flashes, press the START/STOP button to make the numbers scroll until you reach the desired value : 45 s. When T1 flashes, press SPLIT/RESET for a longer time to go to the setting of the number of repetitions of the sequence. The number between the square brackets will flash and indicate the number of repetitions of the GLOBAL sequence. This number can be changed for the whole series when setting each timer : 3 s. When T1 flashes, press START/STOP to go to the settings mode for the following timers. The starting values set for each timer will be displayed on the bottom line. The number of repetitions of the total sequence will be displayed to the right of the repetition counter: ex, in our case [000]/03. · Use The START/STOP button starts or stops the countdown. When the countdown has stopped, press the SPLIT/RESET button to reinitialize it at its set value. The repetition counter (between the square brackets) goes up by 1 unit. Then the countdown begins again at its initial value and counts the same interval of time again. A press on SPLIT/RESET will reset the repetition counter to 0 and reinitialize the countdown at its starting value. [. . . ] Once the number 99 is reached, the counter will flash to signal that the memory is full. Display of the word FULL. START/STOP : start/stop the stopwatch RECALL : recall of intermediate times recorded SPLIT/RESET : to record an intermediate time MODE : go to the following mode Display ·Top line ::the current value of the stopwatch - Middle line : LAP, the time around - Bottom line : SPLIT, the intermediate time In this mode, the screen will display the letters STW in the middle of the screen when the stopwatch is functioning. When the stopwatch has stopped (START/STOP), the last lap is put into memory. memory · Using the the stopwatch, the first 99 intermediate times and lap times are memorized. When using They can be recalled, whether the stopwatch is in action or not, by pressing the RECALL button. [. . . ]