User manual GENIUS DSC13M SMART

[. . . ] 9. Low temperatures (below 10C) may reduce the output efficiency of batteries, thereby shortening the operation time of camera. 10. If battery leakage happens, please remove batteries from the compartment and clean the base before loading the new batteries. 11. If you accidentally touch or get leakage stains on clothes, please wash with clean water. [. . . ] 2. Type D:\SETUP. EXE, WHERE D: is the designation of your CD-ROM drive, then press the Enter key. 2. Do not use different types of batteries together, or mix old and new batteries. Caution for battery usage Please follow these instructions to install the batteries. Uninstall: 1. Click the Start button on Windows Taskbar, and choose Programs > DSC-1. 3M Smart> DSC-1. 3M Smart Uninstall 2. Follow the uninstall steps 3. restart computer 2. Connect DSC-1. 3M Smart to your Computer 1. When prompted, connect the DSC-1. 3M Smart Camera to the USB port of your computer, as shown in the drawing. 1. Check the polarity marks on the battery ( + and - ) before loading the batteries in the camera. 2. Turn the camera off before removing the batteries. USB connector Getting to Know Your Camera follows: Front view 1. Battery Cover Loading the Batteries 1. Turn off the power of the camera. 2. Open the Battery Cover. then insert the batteries as shown on the inside of the cover. 3. Close and lock the battery cover. NOTE: We recommend that you gently open the battery cover to avoid damaging it. Button Modes Shutter button: Press this button to take pictures or to capture video. Select button: Press this button to change mode in the required function. Power/Mode button: Press this button to power on your camera or switch to required function. The sequential order of functions is as Auto Power OFF Function If no operation is carried out for a fixed amount of time (about 30 seconds), the power is turned OFF to prevent battery wear. This is called Auto Power OFF. Battery Life Indicator (1) Note: If your batter power is low, you can't use the Flash light any more but you still can use the camera. Full Battery Power (2) Low Battery Power Basic Operation Turn on the power of the camera. (At this time, you will hear one beep. ) The LCD will display and add up the number of pictures taken. When the internal memory is full, the camera will beep, then you will see FULL appears on the LCD. No photos can be taken after this. LCD Description (1) (2) Turn on the power of the camera. Movie recording (1) Three Auto-Shot Mode (2) Self-Timer Press Mode button once and you will see this icon flash. The camera will start to record video. (3) Flash (4) Motion Movie Mode (3) (4) (5) Still Image Mode Press Shutter button to stop recording. You can use the USB cable to download images to a PC. (6) Still Image Quality (7) Still Image Resolution (8) White Balance Mode Three Auto Shot Press the Mode button once and the icon flashes. Press Shutter to confirm, then press Shutter again, the camera will take a picture three times automatically. (9) Image/Movie Counter (10) Delete e (11) Battery Life Indicator Image Resolution Press the MODE button twice and you will see the Press the Select button to change the Resolution mode. F(Fine): High Quality: default value N(Normal): Low Quality icon flash. Power On/Off Press the Power/Mode Button and hold it for a second. The power is on after you hear beeps. White Balance Mode Press the Mode button five times and the icon flashes. Then you can press the Select button to change White Balance Mode. Using the Self-Timer Press the MODE button once Auto: Sunny: Cloudy: and you will see the icon flash. Press the Select button until the icon of Self-Timer appears, then press Shutter to confirm (and you will hear one beep from the camera). The camera will beep for 10 seconds. After 10 seconds, the camera takes a picture automatically. Deleting Images Delete recorded video or images. [. . . ] Charging is completed when the FLASH indicator Force Flash Mode stops blinking. When the icon blinks, you can't use the flashlight. Click Camera/Scanner button then click the Acquire button . Choose the picture that you have taken on the Click New button then the following Album screen will appear. image list and click the Transfer button to transfer the picture from the camera to the application or click the Save button to download the picture or video to the computer. Second: Connect the camera to PC and you will see this icon appear on the LCD display. [. . . ]