User manual GENIUS D613-R1

[. . . ] English FCC STATEMENT This device complies with Part 15 of the FCC Rules. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Light Frequency Select the correct frequency type (50Hz or 60Hz) according to your region. -29- English 8. Format Media NOTE If the memory card has been inserted, it would only format the memory card, and not the internal memory. Reset to Default Factory Anticipated Settings 4-5 PC Mode -30- English Chapter 5 Preparing Your Camera 5-1 Attaching the Strap Insert the thin end of the strap into the strap holder. . Pass the other end of the strap through the loop. Pull the strap tightly. -31- English 5-2 Loading Batteries Turn the camera off first. If the batteries are low power, please change the batteries as soon as possible to maintain operation normality. NOTE If the battery power indicator only shows one black block, the flash light would be disabled: If lower than 1. 8V (when the battery power indicator turns red) the camera would automatically turn off. Slide the battery cover open in the direction indicated by the arrow. Insert the batteries according to the indication on the inner side of the cover. -32- English Close and lock the battery cover. NOTE Do not open the cover roughly to avoid damaging the battery compartment cover. If the battery power indicator only shows one black block, the flash light would be disabled. When the battery indicator turns red, recording of still pictures and movies would be disabled. The Date/Time would be stored for approximately 3 minutes during battery change. However, double-check the correct Date/Time after the new batteries have been inserted. 5-3 Loading and Removing the Memory Card Turn off the power of the camera first. Loading the Memory Card Memory card insertion diagram. Insert the memory card according to the indicated arrow. Removing the Memory Card -33- English Press the memory card down gently first. The memory card would pop up automatically. Remove the memory card according to the indicated arrow. Attention Before using the camera, please remember to insert the memory card into the slot. If the memory card is full or contains other images, you can press the Mode Button to Format of the Setup Mode to format the memory card. There is 32MB internal memory built-in in the digital camera for Image Storage. If the memory card is inserted, it will be the top priority for saving data. NOTE The specification of memory card applicable for this camera is SD or MMC (8MB~512MB). Please turn off the camera first when inserting/removing the SD memory card. Please don't take out SD card while shooting or playback images to avoid damage risk on SD card or camera. -34- English If the memory card is inserted from the wrong direction, it would not be fitted in. If the camera does not detect the memory card, please gently wipe the metal interface of the card with a soft cloth and reload the card again. 5-4 Setting Up the OSD Language Before using the camera, please select "Language" to set the OSD language by pressing the Mode Button for 2 seconds to Setup Mode . 5-5 Date/Time Before using the camera, please select "Date/Time" to set the date for 2 seconds to Setup and time by pressing the Mode Button Mode . Chapter 6 Getting Started -35- English 6-1 Setup Mode By using the Setup Mode, you can adjust the basic camera settings, including: Image Size, Image Quality, White balance, and EV Compensation. Setup for language, date/time and light frequency is as follows: 1. Press Mode Button for 2 seconds to enter Setup menu and use Function key move to 3. Button to get to into Setup Mode screen, the LCD monitor will display the menu. to move between selections; selections with " " and " 6. [. . . ] You may operate the PC camera through the software that comes with the CD-ROM or other software. to is Chapter 7 Installing the Camera Driver -44- English 7-1. Installing the Camera Driver in PC You can use the "Mass Storage" and "PC Camera" functions of the camera in the PC. The Auto-run program will be executed and the welcome screen will appear the following message: (If your CD-ROM drive doesn't support the auto-run function, please double click on the "My Computer" icon on the desktop. [. . . ]