User manual GENI ELECTRONICS MOJO COLOR MOC

[. . . ] To do this, you need to know that DMX dip switches have the following values: #1 =1; #2=2; #3=4: #4=8; #5=1; #6=32; #7=64; #8=128; #9=256. And you need to know that DMX address settings are the sum of the dip switch values. For example, standard DMX addresses for four MOC changer , each of which has four channels , Follow: MOC Unit 1 Unit 2 Unit 3 Unit 4 Address Value 1 2 3 4 DMX Dip Switches "ON" #1 #2 #1, #2 #3 Mojo ColorTM Product Guide Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Getting Ready. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Install the Lamp (ELC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Lamp Installation (ELC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Installing the Lamp (Figure 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Install the Lamp (EHJ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Lamp Installation (EHJ). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . . . . [. . . ] Please refer to specific product headings in this manual. TM Product Specifications Name: Mojo Color Model: MOC Voltage: 230V~50Hz (CE) Power consumption: 300W Fuse: T3. 15A Dimensions: 280x220x160 mm Weight: 6 kg Lamp: 24V/250W ELC GX5. 3* or 24V/250W EHJ G6. 35* Name: Mojo Color Model: MOC-150 Voltage: 230V~50Hz (CE) Power consumption: 200W Fuse: 5A Dimensions: 280x220x160 mm Weight: 6. 7 kg Lamp: HTI 152W TM TM Name: Mojo Color Model: MOC Voltage: 120V~50/60Hz Power consumption: 300W Fuse: T3. 15A Dimensions: 280x220x160 mm Weight: 6 kg Lamp: 24V/250W ELC GX5. 3* or 24V/250W EHJ G6. 35* Name: Mojo Color Model: MOC-150 Voltage: 120V~50/60Hz Power consumption: 250W Fuse: 5A Dimensions: 280x220x160 mm Weight: 6 . 7kg Lamp: HTI 152W TM TM Warning! Like all electronic products, Mojo Color changer lights must be used with common safety precautions in mind. Disconnect from electric mains power supply before removing covers or changing lamps. If effect lights are dropped or struck, disconnect mains power supply immediately. !This appliance must be earthed. TM *: Versions for other lamps may be produced. Please visit www. geni. com. tw for details. 1 10 Troubleshooting This troubleshooting guide is meant to help solve simple problems. If a problem occurs, carry out the steps below in sequence until a solution is found. If the effect does not operate properly, refer servicing to a technician. Getting Ready All Geni products are thoroughly tested at the factory and shipped in perfect condition. If damage has occurred during shipping or if components are missing, please contact your Geni dealer immediately. Your package should include: TM (1) One Mojo Color color changer with bracket. In most cases, the lamp is not included. No Light, No Movement - All Products Response: Suspect three potential problem areas: the power supply, the lamp, the fuse. See directions above for replacing the fuse. Install the Lamp (ELC) Mojo Color color changer use either the GX5. 3 24V/250W lamp by Osram or the ELC lamp of identical specifications by Philips. Note that product versions that use other lamps may be offered in the future. Check your product specification label for information. TM No Response to DMX Response: Suspect the DMX dip switch setting, DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction. Check the DMX cable: Unplug the unit; change the DMX cable; resupply electrical power. If so, take the DMX cable and the light effect to a qualified technician. Lamp Installation (ELC) (1 ) Loosen the two screws on the top of the lamp cover. (If you touch the bulb glass, wipe off the glass with a clean, lint-free towel and rubbing alcohol. ) (3) Hold the lamp socket with one hand. (5) Put on the lamp cover and fasten the screws snugly. No Response to Audio 1. Turn UD the music volume Lamp Items B A C D E A - Lever B - "ELC" Lamp C - Lamp Base D - Lamp Socket E - Lamp Pins Figure 1 IInstall the Lamp (EHJ) Mojo ColorTM use either the HLX 64655 24V/250W lamp by Osram or the EHJ lamp of identical specifications by Philips. Note that product versions that use other lamps may be offered in the future. 9 2 Lamp Installation (EHJ) (1) Loosen the two screws on the top of the lamp cover. (If you touch the bulb glass, wipe off the glass with a clean, lint-free towel and rubbing alcohol. ) (3)Glove your hand before installing the lamp. Remarks: To replace the lamp, using a small flat-head screw driver to push the lamp out of the lamp socket. Maintenance Mojo Color color changers require almost no maintenance. [. . . ] Do not supply power before the whole system is set up and connected Properly. 4 Four-unit Audio Set Up DMX IN IN OUT DMX Set Up DMX IN IN OUT DMX OUT DMX IN IN OUT DMX OUT DMX IN IN OUT DMX OUT DMX OUT DMX IN DMX OUT IN OUT DMX IN IN OUT DMX OUT DMX IN IN OUT DMX OUT DMX IN IN OUT DMX OUT Power DMX512 SIGNAL Power DMX512 SIGNAL Power DMX512 SIGNAL Power DMX512 SIGNAL Power DMX512 SIGNAL Power DMX512 SIGNAL Power DMX512 SIGNAL Power DMX512 SIGNAL Unit 1 Unit 2 Unit 3 Unit 4 Unit 1 DMX Controller DMX OUT Note: Link cables and set dip switches before connecting electric power. To do so, flip "on" DMX dip switch #1 on the 5th, 9th, 13th, etc. , unit. Then repeat settings on following units, so 6th, 10th, 14th, etc. , unit DMX settings = unit 2 settings; 7th, 11th, 15th, etc. , Unit DMX settings = unit 3 settings; 8th, 12th, 16th unit settings = unit 4 settings. Unit 2 Unit 3 Unit 4 Note: Link all DMX cables and set dip switches before connecting electric power. Figure 5 7. DMX Control 1. Fasten the effect light onto firm trussing (Use a 30-kg rated or stronger CTM clamp bolted onto the Mojo Color bracket). [. . . ]