User manual GENERAL INSTRUMENT DRC-400

[. . . ] If your TV still does not work with the DRC, try searching for the code (see Searching For Your Code on the back side). Write your TV code in the boxes below for future reference. INSTALLING BATTERIES 6. MADE IN INDONESIA USER GUIDE OVERVIEW The General Instrument DRC Universal Remote Control will control up to four devices, including GI Cable Converters (i. e. , DCT-1000, DCT-1200, DCT-2000, and DCT5000), most TVs and VCRs, and auxiliary components. The DRC requires two fresh AA alkaline batteries and easy programming to control all functions of your Cable Converter, as well as all of the basic functions of your other original remote controls. For best results, please read and perform all instructions listed here. Also, keep these instructions for future reference. Use OK/SELECT* to select menu options, PPV events, and to tune programs from the program guide. [. . . ] On the DRC, press and hold TV (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. During this time, release TV and wait until it's lit continuously. Press the (UP) cursor key once to start the search mode. NOTE: In the search mode, the DRC will send IR codes from its library to the selected component, starting with the most popular codes first. When the component responds to a subsequent key command (e. g. , POWER), the correct device code will be found. CHECKING THE CODES If you have set up the DRC using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment. Perform the following procedure after you have set up your components to find out which four-digit code is operating your equipment. On the DRC, press and hold TV (at least 6 seconds) until you see the mode light sequence start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and will repeat twice. During the sequence, release the TV key and wait until it stays lit continually. Count the number of TV key blinks (e. g. , 3 blinks = 3) and write down the number in the leftmost box below. NOTE: The mode key will not blink if the code digit is a "0". CHANGING VOLUME LOCK Your new DRC is set to control volume of a component through its associated mode (i. e. , through the cable in the Cable mode, through the TV in the TV mode, and through the auxiliary device in the Aux. If your TV is not remote controllable, or if you would like the volume to be controlled by a different component, you can change the Volume Lock setting to control a volume through a non-associated mode (e. g. , through the cable in the TV mode). Changing the Volume Lock setting to the Cable or TV mode will change the volume control for all modes except Aux. , which will continue to control its own volume. If you change the Volume Lock setting to the Aux. mode, all modes (i. e. , Aux. , Cable, and TV) will be controlled by the Aux. mode. NOTE: The volume controls will not operate if Volume Lock is set to VCR mode. To change the Volume Lock setting to the AUX mode: 1. On the DRC, press and hold AUX (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. During this time, release AUX and wait until it's lit continuously. The AUX key light will blink three times, indicating volume has been locked to the AUX mode. Now, whenever you press VOLUME +, VOLUME -, or MUTE on the DRC, volume will be controlled by your Auxiliary Device. PROBLEM: SOLUTION: TV/VCR combo does not respond properly. Some combo units may require both a TV code and a VCR code for full operation. Due to RCA design (19831987), only the original remote control will operate these functions. If original remote control required pressing ENTER to change channels, press ENTER on the DRC after entering the channel number. PROBLEM: SOLUTION: PROBLEM: 2. 2. On the DRC, press and hold a mode key (at least 6 seconds) until you see the programming mode start. [. . . ] DRC does not control home entertainment components or commands are not working properly. Make sure they can be operated with an infrared remote control. 8. To change the Volume Lock setting to the CABLE mode: 1. On the DRC, press and hold CABLE (at least 6 seconds) until you see the programming mode start. Each of the mode key lights will turn off and on sequentially, starting with AUX on through TV, and the sequence will repeat twice. [. . . ]