User manual GENERAL ELECTRIC 25922

[. . . ] Model 25922 Series 5. 8 GHz Cordless Handset System User's Guide · If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this product does not disable your alarm equipment. · If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. 2 Rights of the Telephone Company Should your equipment cause trouble on y our line which may harm the telephone network, the telephone company shall, where practicable, notify you that temporary discontinuance of service may be required. Where prior notice is not practicable and the circumstances warrant such action, the telephone company may temporarily discontinue service immediately. [. . . ] Trademark(s) ® Registered Marca(s) Registrada(s) WARNING: TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THE LIGHTNING FLASH AND ARROW HEAD WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF "DANGEROUS VOLTAGE" INSIDE THE PRODUCT. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). THE EXCLAMATION POINT WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF IMPORTANT INSTRUCTIONS ACCOMPANYING THE PRODUCT. 4. Close the battery compartment by pushing the door up until it snaps into place. Making a Call 1. When finished, press the TALK/CALL BACK button again or place the handset on the base cradle to hang up. Model 25922 00017560 (Rev. 2 Dom E) 07-36 Printed in China SEE MARKING ON BOTTOM / BACK OF PRODUCT Reviewing CID Records As calls are received and stored, the display is updated to let you know how many calls have been received. Press the CALLER ID-VOLUME (6) button to review the newest CID record. Press the CALLER ID-VOLUME (5) button to review the oldest CID record first. Deleting All CID Records 1. Use the CALLER ID-VOLUME (5or6) button to display any Caller ID record. NOTE: Press the *EXIT/tone key to return to the standby mode. Reviewing and Deleting Stored Numbers 1. To review stored numbers, press the mem button, and use the CALLER ID-VOLUME (5or6) button to scroll to the memory location, or press the corresponding number key for a desired memory location (0-9). The display shows DELETED. Display Messages The following messages show the status of the phone or help you set up and use your phone. DELETED EMPTY END OF LIST ENTER NAME INCOMPLETE DATA LOW BATTERY NEW NEW VOICE MAIL NO DATA NO CALLS PAGING FRM BASE PLEASE REGISTER PRESS TALK KEY READY REPT TRANSFERRING UNABLE TO DIAL UNABLE TO STORE UNAVAILABLE Caller information is blocked from transmission. Prompt asking if you want to erase the current Caller ID record that is shown on the display. Prompt asking if you want to erase one of the 10 numbers stored in the phone's outgoing memory. Indicates there is no additional information in the Caller ID memory log. Telling you to name the handset or enter a name for one of the 10 memory locations. Caller information is interrupted during transmission or the phone line is excessively noisy. Indicates the CID number is a Directory Dial Number (DDN) and cannot be formatted. Indicates that a new call from the same number was received more than once. Or there has been a base power failure, in which case you must place all handsets on the main base cradle for 20 seconds to re-register. The incoming call is from an area not serviced by Caller ID or caller information is not sent. Troubleshooting Tips Caller ID Solutions No display · Fully charge (for 16 hours) or replace the battery. · If you are using AC (electrical) power, make sure that the unit is connected to a non-switched electrical outlet. [. . . ] Press the mem button again to replace the old number with the new number. You will hear a confirmation tone. Warranty Assistance If trouble is experienced with this equipment, for warranty information, please contact customer service at 1-800-448-0329. If the equipment is causing harm to the telephone network, the telephone company may require that you disconnect the equipment until the problem is resolved. Any unauthorized repairs, changes or modifications not expressly approved by Thomson Inc. [. . . ]