User manual GENELEC AOW312

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual GENELEC AOW312. We hope that this GENELEC AOW312 user guide will be useful to you.


GENELEC AOW312 : Download the complete user guide (343 Ko)

Manual abstract: user guide GENELEC AOW312

Detailed instructions for use are in the User's Guide.

[. . . ] The amplifier unit contains an active crossover, the ideal method for dividing an input signal between the driver units, allowing the overall response of the system to be optimized to an extent impossible with a passive system. Variable input sensitivity as well as XLR line level input connectors provide easy connection and accurate level matching to the preamplifier or surround decoder. The bass, midrange and treble amplifiers of the AOW312 produce 180 W for the low frequency driver and 120 W each for the midrange and HF drivers. The amplifiers are designed to operate at very low THD and IM distortion values and are capable of driving the AOW312 to peak output levels in excess of 124 dB SPL at 2 m with music material. [. . . ] THIS EQUIPMENT IS CAPABLE OF PRODUCING SOUND PRESSURE LEVELS IN EXCESS OF 85dB WHICH MAY CAUSE PERMANENT HEARING DAMAGE. MAINS INPUT 50 / 60 Hz 300 Watts 115 / 230 V ~ ON DO NOT EXPOSE TO WATER OR MOISTURE. Figure 2. The acoustic axis is located at the indicated height on the centerline of the loudspeaker cabinet. Figure 3. AOW312 loudspeaker cabinet top view at 15° angle. front baffle and the cloth. The reflex port of the loudspeaker cabinet is located on the left side of the cabinet (see Figure 1). The airflow from the port must not be obstructed, and a free space of at least 5 cm (2") is required before the port. Connections Each loudspeaker is delivered with two Speakon cable connectors. There is one Speakon output on the amplifier and two Speakon cable inputs (one on each side) on the cabinet. The inputs may not be used for daisy-chaining several loudspeakers or connecting two amplifiers to a single loudspeaker. Pins 1- and 1+ carry the signal for the tweeter, pins 2- and 2+ for the mid range driver and pins 3- and 3+ for the woofer. The whole cable should have an outside diameter of 8 to 20 mm (5/16" to Cable gauge 2, 0 mm2 (14 AWG) 3, 3 mm2 (12 AWG) 5, 3 mm2 (10 AWG) Max. length 30 m (100 ft) 40 m (130 ft) 60 m (200 ft) 13/16") to fit in the Speakon connector. Alternatively, pre-terminated lengths of cable are available from Genelec. Be sure not to mix the amplifier/loudspeaker pairs when installing multiple loudspeakers at the same time. Each amplifier and loudspeaker delivered in the same box are marked with the same identification number and calibrated together for optimal performance. Leave at least ten centimeters (4 inches) free space above and below the amplifier to ensure cooling. The space adjacent to the amplifier must either be ventilated or sufficiently large to dissipate heat so that the ambient temperature does not rise above 35 degrees Celsius (95°F). There are no fans in the amplifier unit so it may be mounted in the listening room near the lodspeaker cabinet using a short cable. Check that the mains voltage selector is correctly set to your local voltage. Audio input is made via a 10kOhm balanced XLR connector, but unbalanced leads may be used as long as pin 3 is grounded to pin 1 of the XLR. Once connection has been made, the loudspeakers are ready to be powered-up. output of the decoder or other source, by use of the input sensitivity control on the amplifier panel. The manufacturer default setting for this control is -6 dBu (fully clockwise) which gives an SPL of 100 dB @1m with a -6 dBu input level. To get the full output level from the AOW312 an input level of +10 dBu is needed at this setting. Autostart and remote control The AOW312 is equipped with an "Autostart" function, which automatically turns the amplifier to "standby" mode if an input signal has not been detected for approximately thirty minutes, and back to "on" mode when the signal returns. The function can be deactivated by turning the "AUTOSTART" dip switch to "OFF". A two-colour LED on the amplifier panel indicates the amplifier status: green for "on" and yellow for "standby". [. . . ] REFER TO O PERA TING MANUAL FOR MAX IMUM S PL. HT312A ACTIVE HOME THEATER SYSTEM GENELECR MAGNE TICA LLY SHIE LDED SIGNAL INPUT 1 55 (2 5/32") www. g en elec. com MADE IN FINLAND SERIAL NUMBER 3 P IN 1 = GROUND P IN 2 = + INPUT P IN 3 = - INPUT 2 MAINS V OLTAGE S ELECTOR WARNING ELECTRIC SHOCK HAZARD! IT IS FORBIDDEN TO UNDO ANY SCREWS ON THIS EQUIPMENT. SERVICING AND ADJUSTMENT MUST ONLY BE CARRIED OUT BY QUALIFIED SERVICE PERSONNEL. NEVER OPERATE THIS EQUIPMENT WITHOUT A PROPER EARTHED MAINS CONNECTION. MAINS INPUT 5 0 / 60 Hz 3 00 Watts 1 15 / 230 V ~ ENSURE THAT THE CORRECT VOLTAGE IS SELECTED BEFORE CONNECTING TO THE MAINS SUPPLY. THIS EQUIPMENT IS CAPABLE OF PRODUCING SOUND PRESSURE LEVELS IN EXCESS OF 85dB WHICH MAY CAUSE PERMANENT HEARING DAMAGE. Figure 10: AOW312 loudspeaker cabinet ON DO NOT EXPOSE TO WATER OR MOISTURE. AOW312 Operating Manual system specifications aoW312 Lower cut-off frequency, -3 dB Upper cut-off frequency, -3 dB Free field frequency response of system Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz Maximum long term RMS acoustic output in same conditions with IEC-weighted noise (limited by driver unit protection circuit) Maximum peak acoustic output per pair above console with music material Self generated noise level in free field @ 2 m on axis Harmonic distortion at 95 dB SPL at 1m on axis: Drivers Bass Midrange Treble Weight Loudspeaker Amplifier Loudspeaker dimensions Height Width Depth Amplifier dimensions Height Width Depth <35 Hz >22 kHz 37 Hz - 21 kHz (±2. 5 dB) @ 1 m >116 dB SPL Bass amplifier short term output power Midrange amplifier short term output power with an 8 Ohm load Treble amplifier short term output power with an 8 Ohm load amplifier section aoW312 180 W (4 Ohm load) 120 W 120 W Long term output power is limited by driver unit protection circuitry. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE GENELEC AOW312




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual GENELEC AOW312 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.