User manual GENELEC AIW26

[. . . ] If you prefer a diffuse sound field, which is less critical to the listening position and gives only a vague sense of direction, for instance in a rear/side channel setup in a Home Theater system, you may actually benefit from the acoustical reflections from nearby boundaries. In this case, place the speakers close to the ceiling or another wall, or have them face away from the listening position, so that the proportion of reflected sound increases. Unpacking A Genelec AIW26 set includes the following items. If there is a problem with the product, contact your local Genelec dealer. · · · · · · · · · AIW26 loudspeaker unit with two mounting brackets attached. [. . . ] Use a wide piece of wood or plastic to wedge the insert out. Painting the speakers The speaker grill frame and the metal mesh part of the grill insert can be spray painted to match the wall colour. Do not paint the speaker cabinet itself, or try to paint the grill frame or grill insert while they are attached to the speaker. Remove the metal mesh from the grill insert to avoid clogging the grill insert cloth with paint. Be very careful not to clog the holes on the mesh with paint. Connecting the RAM1 amplifier The RAM1 amplifier is designed to be connected to a line level output of a preamplifier, Surround Sound processor or other low level source. Never connect the RAM1 to a speaker level output of a power amplifier!Before making the connections, check that the voltage selector on the amplifier's back panel is set to the correct voltage and the power on all components is turned off. Start by connecting the speaker cables to the amplifier's binding posts (see Fig. Check that the amplifier's serial number matches that of the AIW26 speaker unit which it will power. The number can be found on a sticker on the speaker's reflex port and on the amplifier's top cover. If the speakers are not yet installed, make a note of which amplifier is connected to each channel so you can find the correct AIW26 speaker unit for every amplifier. Check the cable polarity and use the provided cable binding post tool to tighten Installing the AIW26 speaker unit Use the cardboard wall cut-out template to find the location for the AIW26. The template also shows the position of the speaker drivers, so you can easily find the placement that brings them to the optimum position as outlined in chapter "Speaker placement". Examine the wall structure carefully to find a clearly unobstructed location for the speaker. The speaker cabinet requires a minimum of 88 millimeters (31/2") of free depth behind the sheetrock. Lift the mounting brackets up and push the lower end of the speaker into the cut-out Figure 5. Pull the mounting brackets down and attach the grill frame Figure 6. If you have lost the cable binding post tool then a large screwdriver will also work, but be careful not to overtighten the binding posts as they may be damaged. The RAM1 has two parallel 10 kOhm input connectors: a balanced XLR and an unbalanced RCA. For longer cable connection lengths (>10m or >30ft) a balanced line connection is recommended as it offers better immunity to external interference. However, the RCA connection method is more commonly available and usually works as well for shorter connection lengths in less electrically noisy environments. The RAM1 has a provision for remote controlled switching between "ON" and "STANDBY" modes. The "REMOTE CONTROL" connector block has two connector pairs: 1-2 for a 12 V DC trigger remote control and 3-4 for an external switch or relay type (contact closure) remote control (see Table 2). [. . . ] If you are using a remote control to switch the RAM1 between "STANDBY" or "ON" modes (see chapter "Connecting the RAM1 amplifier"), turn switch 3 (REMOTE CONTROL), on the first switch group to "ON". In this setting the remote control will override the Autostart function. If you want to use Autostart, turn the "REMOTE CONTROL" switch to "OFF". WARNING! This equipment is capable of delivering Sound Pressure Levels in excess of 85dB, which may cause permanent hearing damage. Guarantee This product is supplied with a two year guarantee against manufacturing faults or defects that might alter the performance of the unit. Refer to supplier for full sales and guarantee terms. EC Declaration of Conformity This is to certify that Genelec AIW26 I-wall Speaker System conforms to the following standards: Safety: EN 60065 / IEC 60065:1998 7th Edition EMC: EN 55013: (2001) EN 55020: (1994), A11: (1996), A12: (1999), A13: (1999), A14: (1999) EN 61000-3-2 (2000) EN 61000-3-3 (1995) The product herewith complies with the requirements of The Low Voltage Directive 73/23/EEC, EMC Directive 89/336/EEC and 93/68/EEC Maintenance There are no user serviceable parts within the loudspeaker or the amplifier. [. . . ]