User manual GE AGE21DH

[. . . ] www. GEAppliances. com Air Conditioners Room Safety Instructions . . 6 Installation Instructions Preparing to Install the Air Conditioner . . 8­12 Owner's Manual and Installation Instructions AGE14 AGE18 AGE21 Troubleshooting Tips . . 19 Write the model and serial numbers here: Model # __________________________ Serial # __________________________ Find these numbers on a label on the side of the air conditioner. 3828A20514N 49-7508-1 03-05 JR Safety Instructions IMPORTANT SAFETY INFORMATION. [. . . ] These models should be installed on their own single branch circuit for best performance and to prevent overloading house or apartment wiring circuits, which could cause a possible fire hazard from overheating wires. Level Scissors or knife Power cord includes a current interrupter device. The device should be tested on a periodic basis by first pressing the TEST button and then the RESET button. If the TEST button does not trip or if the RESET button will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician. 7 Installation Instructions PARTS INCLUDED (Appearance may vary) Window sash seal Left accordion panel Top mounting rail Top mounting rail seal strip Foam top window gasket Frame guide (2) Right accordion panel Sill bracket (2) Window locking bracket Support bracket (2) Type A (14) Type B (7) Type C (5) Type D (2) Carriage Bolt (2) Lock Nut (4) 8 Installation Instructions 1 WINDOW REQUIREMENTS · These instructions are for a standard double-hung window. · The air conditioner can be installed without the accordion panels if needed to fit in a narrow window. · All supporting parts must be secured to firm wood, masonry or metal. · The electrical outlet must be within reach of the power cord. 2 STORM WINDOW REQUIREMENTS A storm window frame will not allow the air conditioner to tilt toward the outside, and will keep it from draining properly. WOOD PIECES­ WIDTH: 2 LENGTH: Long enough to fit inside the window frame. Measure and mark 11 to the left and right of the centerline. Centerline 11 11 F Pull the accordion panels to each window 6 INSTALL THE CASE IN THE WINDOW A Align the inside edge of the sill brackets with the 11 marks from the centerline and attach them to the window sill using 2 type B screws on each side. stool aligning the center front on the bottom with the centerline marked on the window stool. Close the window making sure the window sash is behind the top mounting rail. sash track. Attach them on each side to the window sash and the window stool using 4 type C screws. B Carefully place the case on the window C Using the larger diameter hole in the case, attach the brackets to the case using two type D screws and 2 lock nuts on each side. 11 Installation Instructions 7 INSTALL A SUPPORT BRACKET 8 INSTALL THE AIR CONDITIONER AND THE FOAM TOP WINDOW GASKET A Attach a support bracket with a Type C screw. IN THE CASE A Slide the air conditioner into the case. Reinstall the 2 screws removed earlier on each side of the case. vent control lever located above the unit control knobs, as shown. B Before installing the front grille, pull out the B Cut the foam top window gasket to the window width. foam between the glass C Stuff theto prevent air and insectsand the window from getting into the room. C Attach the front grille to the case by inserting the tabs on the grille into the slots on the front of the case. Push the grille in until it snaps into place. Guide the lever carefully through the grille as you push it in. D Lift the inlet grille and secure the front frame with a type A screw through the front grille. Lower the inlet grille back into place. 12 Before you call for service. . . Troubleshooting Tips Save time and money!Review the chart below first and you may not need to call for service. Problem Air conditioner does not start Safety Instructions www. GEAppliances. com Possible Causes The air conditioner is unplugged The fuse is blown/circuit breaker is tripped Power failure What To Do · Make sure the air conditioner plug is pushed completely into the outlet. · Check the house fuse/circuit breaker box and replace the fuse or reset the breaker. When power is restored, wait 3 minutes to restart the air conditioner to prevent tripping of the compressor overload. · If the RESET button will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician. · Set the mode control at FAN or HIGH COOL with the temp control at a warmer setting. · Make sure there are no curtains, blinds or furniture blocking the front of the air conditioner. · When the air conditioner is first turned on you need to allow time for the room to cool down. [. . . ] s In commercial locations labor necessary to move the unit to a location where it is accessible for service by an individual technician. s Damage to the product caused by improper power supply voltage, accident, fire, floods or acts of God. s Incidental or consequential damage caused by possible defects with this air conditioner. s Damage caused after delivery. Installation Instructions Troubleshooting Tips This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. [. . . ]