User manual GE PHONE MODEL 27907

[. . . ] Model 27907 Series DECT 6. 0 Cordless Handset Speakerphone Answering System User's Guide Your new GE telephone system is EXPANDABLE up to a total of 4 handsets (by purchase of optional Model 27907 handset with charge cradle) Equipment Approval Information Your telephone equipment is approved for connection to the Public Switched Telephone Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the Technical Requirements for Telephone Terminal Equipment published by ACTA. 1 Notification to the Local Telephone Company On the bottom of this equipment is a label indicating, among other information, the US number and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to your telephone company. The REN is useful in determining the number of devices you may connect to your telephone line and still have all of these devices ring when your telephone number is called. [. . . ] 1 NOTE: Adjust the handset volume by pressing the caller ID-volume ( 6 or 5) button during a call. Call Timer After you press the TALK/CALL BACK button on the handset, the built-in call timer shows on the display and counts the length of time of the call in minutes and seconds. Auto Standby If you place the handset in the cradle while the handset is off the hook (during a call), the call is automatically disconnected. Ringer HI/LO/OFF (Shortcut) There are two ways to set the ringer to HI/LO/OFF. One is the traditional way as described in the Programming Functions; Handset Setup; Ringer Volume menus. Use the touch tone pad on the handset to select 1, or , or use the caller ID-volume (6 or 5) button to scroll to your selection. Press #pause/ringer button again to save and display the new selection for a few seconds. Flash/Call Waiting If you subscribe to the combined Call Waiting Caller ID service from your local telephone company, you will receive Caller ID information (if available) on Call Waiting calls. During a phone call, you will hear a beep to indicate another call is waiting on the line and Caller ID information for the waiting call shows on the handset display. · To connect to the waiting call, press the flash/answerer button on the handset, and your original call is put on hold. · To switch between the two calls, press the flash/answerer button. TIP: Do not press the TALK/CALL BACK button on the handset to activate a custom calling service, such as call waiting, or call will disconnect. Last Number Redial You may redial a number up to digits long. Press the redial button first, then use the caller ID-volume ( 6 or 5) button to select the desired redial number. - Press the caller ID-volume ( 5) to review the oldest call and scroll toward the most recent calls (higher numbers). - Press the caller ID-volume ( 6 ) to review the newest call and scroll to older calls (lower numbers). If you get a busy signal and want to keep dialing the number, press the redial button to quickly redial the number. Exit Press the exit button to exit a menu function and return to the standby screen. Page The page feature helps you locate a misplaced handset. If your handset is not registered, follow the instructions in the Registration section of this manual. Handset to Handset Paging (applicable only with additional handsets) 1. To cancel the page, press the exit, int, or TALK/CALL BACK button on the originating handset, or press the exit button on the receiving handset. Paging All Handsets from a Handset (applicable only with additional handsets) 1. (1= to page Handset 1, =to page handset , etc. , and 5=to page all handsets) . To cancel the page, press the exit, int, or TALK/CALL BACK button on the originating handset, or press the exit button on the receiving handset. 5 Paging from the Base/Group Page Use the base-only to page all registered handsets at the same time. All handsets beep for two minutes, and PAGING FROM BASE shows on each handset's display. To cancel the page, press the page button on the base, or press the TALK/CALL BACK button or the exit button on each handset. Mute To have a private, off-line conversation, use the MUTE feature. The party on the telephone line cannot hear you, but you can hear them. Press the mute/program button to cancel and return to your phone conversation. Receiver Volume Control When the handset is ON (in talk mode) you may adjust the receiver volume by pressing the caller ID-volume ( 6 or 5) button. When the maximum or minimum volume level is reached, the phone beeps twice. [. . . ] (The warranty period for rental units begins with the first rental or 5 days from date of shipment to the rental firm, whichever comes first. ) What we will do: · Provide you with a new or, at our option, a refurbished unit. The exchange unit is under warranty for the remainder of the original product's warranty period. Include any cables, etc. , which were originally provided with the product. · "Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period, must be presented to obtain warranty service. " For rental firms, proof of first rental is also required. [. . . ]