User manual GARY FISHER CYBER COMPUTER

[. . . ] Awareness of potential road, trial, or traffic problems should be your main concern. Speedometer (miles or kilometers) (SPD) (M/hr or KM/hr) Tells you your instantaneous speed. Accurate to 0. 1 mph or Kmph SPD/STP Cumulative Odometer (ODO) Stores your total mileage for the year in tenths of a mile or km from 0 to 9999. 9 and in full miles or km from 10, 000 to 99, 999 SPD/ODO Automatic Ride Time Stopwatch (STP) Stopwatch that starts and stops when your wheel is turning. Records your time actually spent riding, up to 9:59:59 Trip Odometer (DST) Tells you the distance for your current ride from 0 to 999. 99 mi. [. . . ] Install the battery so that the positive "+" side of the battery is visible, and replace the battery cover. CAUTION: On the bottom of the computer head next to the battery door is a small recessed button. Pressing this button will clear all memories and reset all functions to their default values. 1. Position the sensor unit to the inside of either the right of left fork blade anywhere from 3-6 inches up from the fork blade tip. Route the sensor wire up the back of the fork blade or wind the wire around the blade, making sure that the wire is not loose and that you leave enough wire to reach the handlebar. Secure the wire to the fork blade immediately above the sensor and at the top of the fork blade, using the adhesive strips that are provided or electrical tape. The Fisher Cyber Computer attaches to the mounting bracket by sliding the unit onto the bracket from the back until it snaps firmly into position. To remove the computer from the bracket, place your thumb against the back of the mounting bracket and pull the computer toward you with your index finger. 5 Setting the Clock, Thermometer and Miles or Kilometers 1. The screen will clear and Mi, F and 12 will appear indicating the American calibration settings. Press the START/STOP key to change to the Metric settings if desired, or press the MODE key to set screen and advance to Adjusting the Clock 4. Press the MODE key to set the screen and advance to setting the Minutes in the same manner as Hours. Press the MODE key one final time to set the screen and return to the main screen . Wheel Size Setting The wheel size setting number is equal to the distance, in millimeters, that your front wheel travels during one complete revolution. Each time the wheel magnet passes the sensor unit on your fork, the sensor sends an impulse to the computer telling it that your wheel has completed one revolution. time to give you accurate readings for the various modes. Determining Wheel Size Setting There are three methods for determining the wheel size setting. For the most accurate computer readings, it is best to measure the actual distance that your wheel travels in one complete revolution. Method One: Wheel Roll Out Method Two: Measure wheel radius (including tire) in mm and multiply by 6. 2832=Wheel setting number. Method Three: Refer to the following chart and input the number that corresponds to your tire size. (Note: Actual size of two similarly marked tires from different manufactures can vary significantly, making this method the least accurate. ) WHEEL SIZE CHART Wheel/Tire Size Wheel Size Setting in mm 26 x 1. 0 ATB . . 2110 The Cyber is equipped with 3 buttons that conrol the functions of the unit: 1. START/STOP Starts and stops the Stopwatch in the Workout Window and adjusts the digits when setting he Clock, Wheel Size and Odometers. PROGRAMMING YOUR FISHER CYBER CYCLE COMPUTER We will now begin to program the features of he Cyber. Take a few minutes to familiarize yourself the operation of the buttons and how he Cyber operates before proceeding. [. . . ] Once the START/STOP key is pressed the action of the Stopwatch is automatic, starting and stopping when the wheel of the bike is turning. The Workout Window icon will flash to indicate that the Workout Window is operating. Pressing the START/STOP key for 2 seconds in the main SPD/STP screen will reset all functions, both main and Workout Window 2. Pressing the START/STOP key for 2 seconds in the WORKOUT WINDOW SPD/STP screen will reset only the WORKOUT WINDOW functions and will not affect the Normal Operating functions. [. . . ]