User manual GARMIN SL 30 NAV/COM

[. . . ] Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U. K. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that such electronic or printed copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited. Garmin reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes or improvements. [. . . ] Using this feature, you may leave the audio enabled and then control it by an external audio panel. Automatic Morse Code Decode/Display The Morse code identifier will not be available until two messages have been successfully received, which may take from 15-60 seconds depending on conditions. When no voice is present on the station, the Morse code identifier is decoded correctly at least 99. 5% of the time. If the station is transmitting voice along with the Morse Code identifier, the probability of the SL30 to decode the identifier drops to 95%. Voice or poor reception (such as the station is far away) may delay or inhibit the automatic decode function. 18 Advanced Operation Saving a Nav channel Nav Mode You can save the frequency in the Standby position and give it a name of up to four characters. Additional information can be saved along with the name, if the selection is a Localizer or ILS. ILS selections may include the runway number (01-36) and designation (L, R, or C). After 250 Nav and Com frequencies are saved, you will get a "Database Full" message. The right side of the display will show "store as" with a flashing cursor. 108. 10 s111. 10 store as _ ils 2. If it is a Localizer frequency, after you turn the LARGE knob one position clockwise past the fourth character, the LOC label will flash. Turn the SMALL knob to choose L, R, or C to identify the runway, as desired. Press the SEL button if you do not want to save the frequency. Removing a Nav channel You may only remove channels stored in the User list. 1. You may also press SEL again to cancel the process. 19 Advanced Operation Nav Mode Recalling a Nav channel There are several lists of channels that you can recall from memory in Nav mode. Remote Localizer, remote VORs, the ten most recently used channels in Nav mode, and the userstored channels. 1. Press the FLIP/FLOP button to select this entry as the active channel. NAV Stored Frequencies and DST Data* Press . Turn LARGE Knob , then turn SMALL knob . Remote ILS Frequencies First Remote VOR Frequencies First Auto Stored List (AUTO) First User Memory (USER) First Distance Speed Time Data * Shown when installed external device is sending data Last Press Last Last Last to insert into Standby. Press to insert into Active. 20 Advanced Operation Remote Localizer List Nav Mode If Localizer channels have been sent by an external device, then this list will be the first displayed for convenience while preparing for a landing. The list shows the airport identifier on the left, a runway identifier for the station in the center, and the channel frequency on the right. If multiple Localizer frequencies are available at the destination airport, the Y symbol will be shown on the right side of the display. The SMALL knob will scroll through the entries in the order they were sent. 111. 80 s117. 40 PDX 10L 111. 30Y Remote VOR list If VOR channels have been sent by a remote device, then this list will be the next available. The channels show the identifier, the "vor" label, and the frequency. 111. 80 s117. 40 UBG vor 117. 40Y Automatic Nav Channel List The last ten used active frequencies are available. [. . . ] The 8-digit number is located on the back of the unit. Serial Number: Product Registration and Support Help us better support you by completing your online registration today!Have the serial number of your SL30 handy and connect to the Garmin Web site (www. garmin. com). Also, be sure to record your serial number in the space provided to the left. If you have any questions, Garmin's Product Support department may be reached Monday through Friday, 8:00 AM to 5:00 PM Central Standard Time, by phone at 1-800-800-1020, or by e-mail at sales@garmin. com. NOTE: If you have previously registered a Garmin product purchase, we invite you to re-register using our NEW on-line system. [. . . ]