User manual GARMIN GHP 10

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual GARMIN GHP 10. We hope that this GARMIN GHP 10 user guide will be useful to you.


GARMIN GHP 10 : Download the complete user guide (1052 Ko)

You may also download the following manuals related to this product:

   GARMIN GHP 10 (1427 ko)
   GARMIN GHP 10 (1442 ko)
   GARMIN GHP 10 (1416 ko)
   GARMIN GHP 10 (1420 ko)
   GARMIN GHP 10 (1417 ko)

Manual abstract: user guide GARMIN GHP 10

Detailed instructions for use are in the User's Guide.

[. . . ] The serial numbers are located on a sticker on each component. Contact Garmin Contact Garmin if you have any questions while using your GHP 10. In the USA contact Garmin Product Support by phone: (913) 397-8200 or (800) 800-1020, or go to www. garmin. com/support/. at +44 (0) 870. 8501241 (outside the UK) or 0808 2380000 (within the UK). Warnings · You are responsible for the safe and prudent operation of your vessel. The GHP 10 is a tool that will enhance your capability to operate your boat. [. . . ] Solder and cover all bare-wire connections. GHP 10 Marine Autopilot System Installation Instructions 1 Wiring the GHP 10 to the Tachometer The tachometer connection is an important part of the GHP 10 system, and must be wired correctly for the autopilot to function. If your engine supports NMEA 2000 engine data, and is connected to the same NMEA 2000 network as the GHC 10 and the CCU, then no other tachometry wiring is necessary. If your engine does not support NMEA 2000 engine data, then wire the GHP 10 autopilot system to the tachometer of your boat using the bare-wire portion of the CCU/ECU interconnect cable. In most cases, this connection can be made behind the dashboard at the tachometer display. Refer to the owner's manual or shop manual for your engine to identify the color codes and location of the tachometer wiring on your boat. To wire the GHP 10 to the tachometer of your boat: 1. Identify the location and wire assignments of the tachometer (or tachometers) on your boat. Route the bare-wire end of the CCU/ECU interconnect cable to the tachometer (or tachometers). If the cable is not long enough, extend the wires with twisted pair, 22 AWG wire. Use the Tachometer Wiring Table to determine the appropriate wires on the CCU/ECU interconnect cable. Connect the tachometer wire or wires from the CCU/ECU interconnect cable to the tachometer sensor wire or wires from the engine ((or engines)). Connect the ground wires to a clean ground. Engine Configuration Single engine Dual engines Tachometer Green and violet (twist together) Port engine = violet Starboard engine = green Tachometer Wiring Table Ground White and grey (twist together) Grey White Note: For three or more outboard engines, connect to the outermost port and starboard engines, according to the table. Note: Stainless-steel screws may bind when screwed into fiberglass and overtightened. Garmin recommends applying an anti-galling, stainless anti-seize lubricant to the screws before installing them. Snap the mounting covers into place to install them. GHP 10 Marine Autopilot System Installation Instructions 1 Wiring the GHC 10 to Power and to the CCU/ECU Interconnect Cable With the GHC 10 power/data cable, wire the GHC 10 to power and to the yellow CCU signal wire on the CCU/ECU interconnect cable. Optionally, you can wire the GHC 10 power/data cable to a NMEA 0183-compatible GPS device to use waypoint and route information with the GHP 10, although a NMEA 2000 GPS device is preferred. To wire the GHC 10 to power: 1. Connect the red (+ or positive) wire to the positive voltage terminal. (If you use the fuse block on the boat, route the positive connection through the fuse. ) 4. Connect the black (- or ground) wire to the negative voltage terminal. Install or check the AGC/3AG ­ 1 A fuse (on the fuse block or in the in-line holder). Do not connect the power/data cable to the GHC 10 until all the connections of the entire GHP 10 system have been completed (page 24). Power/data NMEA 000 · If it is necessary to extend the power wires, use 18 AWG wire. · If your boat has an electrical system, you might be able to wire the GHC 10 directly to an unused holder on your current fuse block. [. . . ] To recalibrate the screws, fully tighten both of them until they stop. If not, loosen the shorter screw until they protrude the same distance. The valve is ready for use. CautioN: Do not unscrew the brass screws more than the specified amount. Do not operate the system with the brass screws fully tightened. 0 GHP 10 Marine Autopilot System Installation Instructions Mounting Templates Use the following mounting templates to assist with the mounting process. ECU Mounting Template CCU Mounting Template Up (when mounting on a vertical surface) GHP 10 Marine Autopilot System Installation Instructions 1 GHP 10 Marine Autopilot System Installation Instructions 1. 2 L/2. 0 L Pump Mounting Template GHP 10 Marine Autopilot System Installation Instructions 2. 1 L Pump Mounting Template GHP 10 Marine Autopilot System Installation Instructions GHP 10 Installation Checklist Detach this checklist from the installation instructions and use it to assist with the GHC 10 installation process. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE GARMIN GHP 10




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual GARMIN GHP 10 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.