User manual GARMIN GSD 22 Installation Instruction

[. . . ] Within this period, Garmin will at its sole option repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost. This warranty does not cover failures due to installation errors, abuse, misuse, accident, or unauthorized alteration or repairs. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED OR STATUTORY, INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, STATUTORY OR OTHERWISE. [. . . ] If any items are missing, contact your Garmin dealer immediately. Included Equipment: · GSD 22 Sounder Module · 6 ft (0. 30 m) Power/Data Cable · 6 ft (0. 30 m) Marine Network Cable · 40 ft (12. 19 m) CANet Extension Cable · 1 Field Install Marine Ethernet Connector · 1 Marine Grommet · 2 CANet Terminators · 7 3-Wire Connectors · The GSD 22 Sounder Module Installation Instructions Optional Transducers The transducer acts as the eyes and ears of your new sonar. The transducer transmits sound waves toward the bottom in a cone shape. The larger the cone angle, the larger the coverage area at a given depth. Proper transducer selection and installation are critical to the operation of your unit. Since mounting locations vary, see your local dealer or contact Garmin Product Support for further information. A full list of transducers can be found at www. garmin. com. Mounting Holes Power/Data Connector Transducer Connector Marine Network Connector GSD 22 Sonar Module 1 INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS The GSD 22 must be properly installed according to the following CANet or Marine Network installation instructions to get the best possible performance. Refer to your chartplotter to determine the correct installation method. If you experience difficulty with the installation, contact Garmin Product Support. The module should be mounted in an out-of-the-way location that is dry and well ventilated. Avoid mounting the module where it can be submerged in liquids or exposed to extreme temperatures. Using the module as a template, mark the location of the four mounting holes. Attach the GSD 22 to the mounting location using appropriate fasteners. Mount the transducer according to the instructions provided with the transducer. Route the cables according to the CANet or Marine Network instructions on the next 3 pages. Use appropriate tie-wraps, fasteners, and sealant to secure the cable along the route and through any bulkhead or deck. After installing the GSD 22 module, connect the power/data and transducer cables to the appropriate receptacle. Refer to the following CANet or Marine Network wiring diagrams for connecting the GSD 22 to compatible Garmin units. NOTE: You can extend the CANet wiring of the GSD 22 power/data cable up to 80 ft (24. 38 m) total length using the CANet Connections Kit. NOTE: You can extend the power wiring of the GSD 22 power/data cable up to 100 ft (30 m) total length using 18 AWG wire. Transducer cable extensions are available through your Garmin dealer. To install the GSD 22 sounder module: GSD 22 Wiring Connection 1. Align the notch and locking ring tab on the black Power cable with the POWER port on the front of the GSD 22. After the cable is seated, turn the locking ring clockwise until it stops. [. . . ] Apply a marine sealant after installation to weatherproof around the grommet and cable. Additional grommets can be purchased from your Garmin dealer or direct from Garmin. Be sure to test the system before installing the grommets. Tools · · · · Drill 1. 25" (31. 7 mm) paddle drill bit or hole saw Utility knife Marine sealant (optional) Mark the location where the cable Power/Data or Garmin Marine Network cable is to route through. Using a 1. 25" (31. 7 mm) paddle drill bit or hole saw, drill the installation hole. [. . . ]